Specifications; Cordless Die Grinder Safety Warnings - Makita DGD800 Betriebsanleitung

ENGLISH
(Original instructions)
1 Button
2 Red indicator
3 Battery cartridge
4 Star marking
5 Slide switch

SPECIFICATIONS

Model
Collet capacity ............................................................................. 6 mm or 6.35 mm (1/4")
Max. wheel point diameter .......................................................... 36 mm
No load speed (n ) / Rated speed (n)........................................... 26,000 (min
0
Overall length .............................................................................. 402 mm
Net weight ................................................................................... 2.0 kg
Rated voltage ............................................................................... D.C. 18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for grinding ferrous materials or
deburring castings.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
CORDLESS DIE GRINDER SAFETY
WARNINGS
Safety Warnings Common for Grinding Operation:
1. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as sanding, wire brushing, pol-
ishing or cutting-off are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
4
Explanation of general view
6 Indication lamp
7 Wrench 13
8 Wheel point
9 Collet nut
10 Wrench 13
5.
6.
ENE050-1
GEA010-1
7.
GEB080-3
8.
9.
10. Never lay the power tool down until the acces-
11. Do not run the power tool while carrying it at
11 Limit mark
12 Holder cap cover
13 Screwdriver
14 Brush holder cap
DGD800
–1
)
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged accessories will normally break apart during
this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of opera-
tion.
Hold the power tool by insulated gripping sur-
faces only, when performing an operation where
the cutting tool may contact hidden wiring. Con-
tact with a "live" wire will also make exposed metal
parts of the power tool "live" and could give the oper-
ator an electric shock.
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
DGD801
6 mm or 6.35 mm (1/4")
36 mm
–1
26,000 (min )
307 mm
1.7 kg
D.C. 18 V