Main Switch; Control Panel - EINHELL GC-RM 500 Originalbetriebsanleitung

ments at a later time.
Using a wire stripper, remove a length of 10 to 15
mm of the insulation at the ends of the perimeter
wire (18) for connecting to the charging station
(19).
Pull out the power plug before you connect the
perimeter wire (18) to the charging station (19).
The perimeter wire (18) laid to the front end of the
charging station (19) must be run to the back via
the cable holders on the underside of the char-
ging station (19). Pass the front perimeter wire
(18) through the guides under the charging stati-
on and through the hole prepared in the connec-
tion area. Connect this wire to the "+" connection.
Then connect the rear perimeter wire (18) to the
"S1" connection (Fig. 7a).
Important! Perimeter wires (18) must not
cross over!
Then connect the power supply. The LED indica-
tor (21) on the charging station (19) should light
up green and stay on permanently. If the LED
does not light up, check the connections fi rst. If
the LED lights up green but not permanently, read
the "Indicators on the charging station and trou-
bleshooting" table at the end of these operating
instructions.
5.7 Switching on and checking the
installation
As soon as the LED indicator (21) on the charging
station (19) lights up green, the mowing area is
ready for the robot lawn mower. Please check fi rst
that all the fastening pegs (14) on the perimeter
wire (18) have been fully tapped in. Place the ro-
bot lawn mower about 3 m to the rear of the char-
ging station (19) in front of the perimeter wire (18).
The robot lawn mower needs to be facing the
perimeter wire (18) at an angle of 90° (Fig. 7b).
Switch on the main switch (7) (ON) (Fig. 8).
Press the POWER button (60) on the control
panel (2) for two seconds. Unlock the robot lawn
mower using the PIN and confi rm the entry with
the "OK" button (61) (see chapter "Locking me-
chanism / PIN").
Press the "HOME / 3" button (64) and then press
the "OK" button again (61). The robot lawn mower
will now follow the perimeter wire (18) in a coun-
terclockwise direction. Observe the robot lawn
mower during the complete trip along the perime-
ter wire (18) until it is back in the charging station
(19). If the robot lawn mower has any problems
at any points, correct the perimeter wire (18) if
necessary and repeat the operation. The rechar-
Anl_GC_RM_500_SPK9.indb 34 Anl_GC_RM_500_SPK9.indb 34
GB
geable battery (22) of the robot lawn mower will
now be fully charged. If any problems occur with
docking, you may need to reposition the charging
station (19) sideways until docking works without
any problems.
To stop the robot lawn mower at any time, press
the red STOP button (3). When you press the
STOP button (3), the robot lawn mower will come
to a stop and wait for further instructions.
5.8 Securing the charging station
Once the robot lawn mower is working properly
and a suitable position for the charging station
(19) has been found, the charging station (19)
must be fi xed in place using the fastening screws
(15). Use the hexagon key (23) to secure the fas-
tening screws (15) fully in the ground (Fig. 7c).
6. Operation

6.1 Main switch

The robot lawn mower is equipped with a main
switch (7). Use the main switch (7) to switch the
robot lawn mower on (ON) and off (OFF) (Fig. 8).
Once the robot lawn mower has been switched
on, it is locked by a PIN.

6.2 Control panel

The robot lawn mower has already been pro-
grammed at the factory and default settings have
been made for it. However, these can be changed
if required. Even though the factory settings will
be suitable for most gardens, you should still
familiarize yourself with the available options ne-
vertheless.
Explanation of the LEDs on the control panel
(Fig. 9a)
50. Time LEDs: Display of the daily mowing time
51. Lock LED: Display of the button lock
52. Battery LED: Display of the battery charge
level
53. Alarm LED: Display of faults
Explanation of the button options on the con-
trol panel (Fig. 9b)
60. POWER button: Switches the robot lawn mo-
wer on and off
61. "OK" button
62. "SET WORK TIME / 1" button
63. "START / 2" button
64. "HOME / 3" button
65. "4" button / Lock button
- 34 -
16.02.2021 14:17:33 16.02.2021 14:17:33