Accessories - Black & Decker KR703 Handbuch

ENGLISH
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
Turn the grip counterclockwise until you can slide the side
u
handle (8) onto the front of the tool as shown.
Rotate the side handle into the desired position.
u
Insert the depth stop (7) into the mounting hole as shown.
u
Set the drilling depth as described below.
u
Tighten the side handle by turning the grip clockwise.
u
Fitting a drill bit or screwdriver bit (fig. B & C)
Keyless chuck with spindle lock (fig. B)
Open the chuck by turning the sleeve (9) counterclockwise.
u
Insert the bit shaft (10) into the chuck.
u
Tighten the chuck by turning the sleeve clockwise.
u
Keyed chuck (fig. C)
Open the chuck by turning the sleeve (11)
u
counterclockwise.
Insert the bit shaft (10) into the chuck.
u
Insert the chuck key (12) into each hole (13) in the side of
u
the chuck and turn clockwise until tight.
Removing and refitting the chuck (fig. D)
Open the chuck as far as possible.
u
Remove the chuck retaining screw, located in the chuck,
u
by turning it clockwise using a screwdriver.
Tighten an Allen key into the chuck and strike it with
u
a hammer as shown.
Remove the Allen key.
u
Remove the chuck by turning it counterclockwise.
u
To refit the chuck, screw it onto the spindle and secure it
u
with the chuck retaining screw.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving
u
parts.
Injuries caused when changing any parts, blades or
u

accessories.

Injuries caused by prolonged use of a tool. When
u
using any tool for prolonged periods ensure you take
regular breaks.
Impairment of hearing.
u
6
Health hazards caused by breathing dust developed
u
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the direction of rotation
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(4) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode
For drilling in masonry, set the drilling mode selector (5) to
u
the position.
For drilling in other materials and for screwdriving, set the
u
drilling mode selector (5) to the position.
Setting the drilling depth (fig. A)
Slacken the side handle (8) by turning the grip
u
counterclockwise.
Set the depth stop (7) to the desired position. The
u
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
u
Switching on and off
To switch the tool on, press the variable speed switch (1).
u
The tool speed depends on how far you press the switch.
If the tool has a variable speed control knob (3), set it to
the required speed range. As a general rule, use low
speeds for large diameter drill bits and high speeds for
smaller diameter drill bits.
For continuous operation, press the lock-on button (2) and
u
release the variable speed switch. This option is available
only at full speed or at any speed preset with the variable
speed control knob (3). This option does not work in
reverse rotation.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory used.