Safety Instructions For All Operations - Black & Decker BEH550 Bersetzt Von Den Originalanweisungen

tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will do the job better and safer at
the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the power
tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power
tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to
be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
5.
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

Safety Instructions for All Operations

● Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
● Use the auxiliary handle(s). Loss of control can cause
personal injury.
(Original instructions)
● Brace the tool properly before use. This tool produces
a high output torque and without properly bracing the tool
during operation, loss of control may occur resulting in
personal injury.
● Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
Safety Instructions when using long drill bits
● Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
● Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
● Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings for drill/ driver/
hammerdrill
● Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the workpiece
by hand or against your body is unstable and may lead to
loss of control.
● Accessories and tool may get hot during operation. Wear
gloves when handling them if performing heat producing
applications such as drilling metals.
● Air vents often cover moving parts and should be avoided.
Loose clothes, Jewellery or long hair can be caught in
moving parts.
● Wear safety goggles or other eye protection. Hammering
and drilling operations cause chips to fly. Flying particles
can cause permanent eye damage.
● Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
● Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
● Do not operate this tool for long periods of time. Vibration
caused by tool action may be harmful to your hands
and arms. Use gloves to provide extra cushion and limit
exposure by taking frequent rest periods.
ENGLISH
5