Storage; Disposal And Recycling; Troubleshooting - Scheppach 5904802907 Original Bedienungsanleitung

Blade with 8 teeth Ø 255 x 1.4
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain ProCut 3/8.50­39
Guide rail ProCut AL10­39­507P
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
Hedge trimmer:
Blade for hedge trimmer 400 mm
Transport guard for blade

11. Storage

Cleaning
• Keep handles free of oil, so you always have a se-
cure hold.
• Clean the equipment as required with a damp cloth
and, if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time be-
fore carrying out any cleaning.
• Never immerse the equipment in water or other liq-
uids in order to clean it.
• Store the petrol multi garden tool in a safe and dry
place out of the reach of children.
Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the follow-
ing steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can
cause problems when starting up the equipment and
may require expensive repairs.
1 Slowly remove the fuel tank cap to release any
pressure that may have formed in the tank. Care-
fully empty the tank.
Only empty the tank out-
doors or in well-ventilated rooms. Make sure that
no fuel or chain oil is released into the soil (en-
vironmental protection). Use a suitable surface.
2 To remove the fuel from the carburetor, start the
engine and let it run until the equipment stops.
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug
5 Add one teaspoon of 2­stroke engine oil into the
combustion chamber. Slowly pull the starter cord
several times to apply a layer of oil to all internal
components. Fit the spark plug again.
Note: Store the equipment in a dry place and far
44 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
7910700711 away from possible ignition sources such as an oven,
3904801066 a gas­fired hot water boiler, a gas­fired dryer, etc.
3904801023 Transport
If you want to transport the tool, empty the petrol tank
7910100732 as described in Chapter 8. Remove major dirt from
7910100731 the unit with a brush.
7910700704 Always attach the transport guard to all cutting tools.
3904801037 Fig. 1 (14a, 15a, 17a)
3904801039 In order to prevent damage and injury, secure the tool
7910700710 against tipping over and sliding when transporting it
in vehicles.
7910700703
3904801043 Putting the equipment back into operation
1 Remove the spark plug (see section 10 Change
2 Quickly tug on the starter cord to remove excess
3 Clean the spark plug and check that the electrode
4 Prepare the equipment for operation.

12. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.

13. Troubleshooting

The table below contains a list of fault symptoms and
explains what you can do to remedy the problem if
your equipment fails to work properly. If the problem
still persists after working through the list, please
contact your nearest service workshop.
and clean the spark plug).
oil from the combustion chamber.
gap is correct, or insert a new spark plug with the
correct electrode gap.