Rinsing The Coffee System - Krups EA870810 Intuition Bedienungsanleitung

When do I empty the coffee grounds collector? see 9 – WARNING LIGHTS (W): EMPTY
THE COFFEE GROUND COLLECTOR, fig 1 to 5.
When the "alert" LED on the interface and the warning light (W) are lit up.
You can periodically empty it before the machine asks you to.
Important:
The coffee grounds collector has enough capacity for about 9 coffee portions; not
regularly emptying the coffee grounds container and drip tray as indicated above
can damage your machine.

Rinsing the coffee system

This function is available at any time, unless the machine requires other maintenance.
– Place a container under the coffee nozzles.
– Switch on your machine then press
– Select the rinse function .
– Press to start rinsing.
Full automatic cleaning program for the machine, 3 times a
year (approximately 13 minutes)
Cleaning the coffee system allows you to combat residue, greasy deposits of coffee and
preserve the flavours of your drinks.
For this cleaning you will need:
– 1 KRUPS cleaning tablet
– 1 container of at least 600 ml
The cycle will link two phases:
– 1 cleaning phase
– 1 rinsing phase
When do I run this program?
When it is necessary to run a cleaning program, the appliance notifies you.
When the machine is switched on, the "alert" LED
light up. See 11 – AUTOMATIC COFFEE SYSTEM CLEANING PROGRAM, fig 1 to 27.
– You can also start a cleaning cycle when you wish: by pressing
cleaning program, indicated by the LED
SYSTEM CLEANING PROGRAM, fig 1 to 27.
Important:
You do not have to run the cleaning program as soon as the appliance requests
it, but you must do it reasonably soon after. If cleaning is postponed, the alert
message will remain displayed as long as the operation has not been performed.
42
.
and the LED on the interface will
and selecting the
. Then see 11 – AUTOMATIC COFFEE
Important:
if you unplug your machine during cleaning or in the event of electrical failure,
the cleaning program will resume the current step at the time of the incident.
It will not be possible to postpone this operation: rinsing the water circuit is
mandatory. In this case a new cleaning tablet may be necessary.
Automatic descaling program (approximately 20 minutes)
Descaling your machine ensures its proper functioning and eliminates any deposit of
limescale or tartar.
Caution: If your appliance is equipped with our Claris Aqua Filter System cartridge
please remove it before the descaling procedure (see "Removing the Claris Aqua
Filter System cartridge").
To perform this cleaning you will need:
– 1 dose of KRUPS descaler
– 1 container of at least 600 ml
The cycle will link three phases:
– 1 descaling phase
– 1st rinsing phase
– 2nd rinsing phase
When do I run this program?
When it is necessary to run a cleaning program, the appliance notifies you. When the
machine is switched on, the "alert" LED
Then, refer to section 12 – AUTOMATIC DESCALING PROGRAM, fig 1 to 30.
Important:
The machine lets you know when it is necessary to do so. However, you can start
descaling the machine at any time by pressing
The Claris Aqua Filter System cartridge
Installation:
– Remove the water tank and empty it. If necessary, remove the used filter cartridge.
– Turn the grey ring located on the upper end of the filter cartridge until it displays the
current date. The cartridge must be changed every 2 months.
– Screw the new filter cartridge into the bottom of the water tank using the accessory
supplied with the cartridge.
– Fill the water tank and put it back in place.
– Switch on the machine by pressing ON/OFF.
– Place an empty container under the coffee nozzles.
– Press and hold "CLEAN"; the indicator lights will flash.
– Then press "START/STOP"; the water will then flow from the coffee nozzles.
– The filter is primed.
Removal:
– Remove the water tank and empty it.
– Remove the filter cartridge.
– Then follow the instructions above, in "Installation", to change the used cartridge.
and the LED on the interface will light up.
and selecting .
43