Metabo ASR 25 L SC Originalbetriebsanleitung Seite 24

en ENGLISH
- Applications, where small amounts of fine dust
are created (e.g. spot-grinding and grinding of
paint and lacquer coatings, extraction of drilling
applications with small diameters < 10 mm of
short duration, etc.).
- Use of machines, such as: routers, planers,
small grinding machines, etc.
Switch off the appliance, remove the mains plug
and open the snap locks (9). Remove the upper
part (8) from the container (10).
paper
"triangle" marking
upwards. (To twist the slide, push it slightly
towards the suction hose, and pull it back after
twisting).
Holding the new fleece filter bag by the flange,
slide the bottom part over the suction connection,
and the top part over the latch pin. Replace the
upper part of the appliance on the container, close
the snap locks.
Hold the fleece filter bag on the flange and, with its
opening, guide it first over the latch at the bottom
part of the suction opening, then fit up to the stop
on the suction opening. Replace the upper part of
the device on the container, close the snap locks.
6.4 Inserting PE filter bag (for ASR 50 M SC
only)
PE filter bags (5) are suitable for both wet and dry
vacuuming.
We recommend the use of PE-disposal bags for:
- Applications, where larger amounts of dust are
created (e.g. removal of plaster surfaces,
spotgrinding and grinding of screeds, etc.).
- Use of machines, such as e.g.: renovation
milling machines, renovation grinders, drywall
grinders, wall grinders etc.
When using a PE disposal bag, the filter cleaning
must be switched on (function AR / IR) for
corresponding materials (see recommendation).
24
ASR 50 M SC: On
the inside of the
suction opening,
push the red rotary
slide with its
ASR 25 M SC:Turn the
red
rotary switch (on the inside
of the suction opening)
until the stop: the text
"CLOSE" shows upwards
to the marking ▲.
Switch off the appliance, remove the mains plug
and open the snap locks (9). Remove the upper
part (8) from the container (10).
plastic
slide with its "circle" marking upwards.
(To twist the slide, push it slightly towards the
suction hose, and pull it back after twisting).
Hold the PE filter bag (5) on the flange and, with
its opening, guide it first over the latch at the
bottom part of the suction opening, then fit up to
the stop on the suction opening.
Spread out the PE filter bag (5) evenly across the
container floor. Arrange the edges of the PE filter
bag around the container rim so that the bag is
firmly clamped on all sides by the upper part (8),
once replaced.
7. The Appliance
7.1 Switching On/Off, Automatic, vibrator Select
operating mode at switch (1):
0=Vacuum cleaner off
I =Vacuum cleaner on (manual operation)
A=Automatic On/Off switch:
The vacuum cleaner is switched on or off
by means of a power tool connected to the
mains socket (3).
R A= Automatic On/Off switch and
Automatic vibrator switch
•
If the switch (1) is turned to position R A,
the electromagnetic vibrator switches on.
Dust is then shaken off the filter. The
vibrator switches off automatically after
approx. 10 s. • In switch position R A, the
vacuum cleaner is switched on or off by
means of a power tool connected to the
mains socket (3).
•
In switch position R A, the electronic
system checks the air flow during work. If
the flow is too low due to a contaminated
filter, the "Filter control" lamp lights up (2).
During the next work break of the connected
ASR 50 M SC:
On
the inside of the
suction opening,
push the red rotary
ASR 25 M SC: Turn the
red
rotary switch (on the inside
o the suction opening) to
the stop: the text "OPEN"
shows upwards to the
marking ▲.