Safety Warnings - Makita DUC256 Betriebsanleitung

Work mode: cutting wood
Vibration emission (a ) : 3.2 m/s
h,W
Uncertainty (K) : 1.5 m/s
Model DUC406
Work mode: cutting wood
Vibration emission (a ) : 3.2 m/s
h,W
Uncertainty (K) : 1.5 m/s
Model DUC256C
Work mode: cutting wood
Vibration emission (a ) : 2.5 m/s
h,W
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with
another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety
measures to protect the operator that are based
on an estimation of exposure in the actual
conditions of use (taking account of all parts of
the operating cycle such as the times when the
tool is switched off and when it is running idle in
addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex
A to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings
WARNING:
Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed
in
and/or
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
2
2
2
2
2
or less
2
below may result
electric shock, fire
serious injury.
Cordless Chain saw safety
warnings
1. Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything. A moment of
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.
2. Always hold the chain saw with your right
hand on the top handle and your left hand on
the front handle. Holding the chain saw with a
reversed
increases the
personal
never
3. Hold the power tool by insulated gripping
surfaces only, because the saw chain may
contact hidden wiring. Saw chains contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
4. Wear safety glasses and hearing protection.
Further protective equipment for head, hands,
legs and feet is recommended. Adequate
protective
personal
debris or accidental contact with the saw
chain.
5. Always keep proper footing.
6. When cutting a limb that is under tension be
alert for spring back.
tension
fibres
loaded limb may strike the operator and/or throw
the chain saw out of control.
7. Use extreme caution when cutting brush and
saplings. The slender material may catch the
saw chain and be whipped toward you or pull you
off balance.
8. Carry the chain saw by the front handle with
the chain saw switched off and away from
your body. When transporting or storing the
chain saw always fit the guide bar cover.
Proper handling of the chain saw will reduce the
likelihood of accidental contact with the moving
saw chain.
9. Follow instructions for lubricating, chain
tensioning and changing accessories.
Improperly tensioned or lubricated chain may
either break or increase the chance for kickback.
10. Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
11. Cut wood only. Do not use chain saw for
purposes not intended. For example: do not
use chain saw for cutting plastic, masonry or non-
wood building materials. Use of the chain saw for
13 ENGLISH
hand configuration
risk of
injury and should
be done.
clothing will reduce
injury by flying
When the
in the wood
is released the spring