Cordivari Claudia Bedienungsanleitung Seite 17

a. Power On / Stand-by mode
Press the key [On/Stand-by] to turn on the device or to enter the "Stand-
by" mode. When activated, the bottom part of the display shows the cur-
rent time, while the configured operative mode and the temperature are
shown in the upper part. When in "Stand-by" mode current time, day of
the week and the message: " Stb" are displayed.
NOTE: When the device goes into "Stand-by" mode it beeps twice for
0.5s.When the device is activated it beeps once for 1s.
Example in "Comfort" mode
Example in "Stand-by" mode
7
b. "COMFORT" and "NIGHT" modes
Two different levels of temperature can be set:
- COMFORT TEMPERATURE is the temperature setting for 'Chrono',
'Fil-Pilote' and 'Comfort'modes;
- NIGHT TEMPERATURE is the temperature setting for the 'Night' and
'Chrono' mode.
The desired temperature can be set pressing the [+] e [ - ] buttons. The
range of configurable temperature is 7°C - 32°C.
IMPORTANT!
The temperature of "Night" mode must be below to the "Comfort" mode
temperature. For this reason the "Night" mode temperature can be set to
a value between 7°C and the (configured "Comfort" mode temperature
- 0.5°C).
The temperature of "Comfort" mode can be configured in the whole
(Night temperature + 0.5°C) ÷ 32°C range.
c. Operating the device
Press the button [Prog] to select the desired operative mode. An icon
on the display indicates the selected operating mode, according to the
following table.
Cod. 1910000000048 - nv03
1 7
2 6
3 5
4
1 7
2 6
3 5
4
1 7
2 6
3 4 5
Pilote wire Comfort
Moreover, the following special functions are also available:
Window opening function
Key lock function
Fil-Pilot mode *
This mode is valid only in the presence of the Fil-Pilot signal, otherwise
the unit will work permanently in "Comfort" mode.
Comfort mode *
The "Comfort" stably maintains the room temperature to a selected
value.To set this operativemode:
1
2 6
3 5
4
-Press the button [Prog] until the display shows the "Comfort" icon .
-Set the desired temperature through [+] and [-] buttons and wait until
the displayed temperature stops blinking.
Night mode
This mode allows saving energy during the night, or in case of infrequent
use of the rooms in which the device is installed. The "Night"mode
sets a value of temperature below the "Comfort" Temperature value.
It is suggested to set this operating mode during the night or when the
room is not occupied for 2 or more hours.
-Press the button [Prog] until the display shows the " Night" icon
-Set the desired temperature through [+] and [-] buttons and wait until
the displayed temperature stops blinking.
Antifreeze mode
In "Antifreeze" mode the temperature is fixed to 7°C. The device
activates the heating element when the room temperature falls below
7°C. It is suggested to set this operating mode when the room is not
occupied for several days. Press the [Prog] button until the display
shows the "Antifreeze" icon.
Timer 2H mode
The "Timer 2h" mode can be used to quickly warm up the room or to
speed up towel drying.
-Press the [Prog] button until the display shows the "2h" icon.
The device is activated at the maximum power for 2 hours, up to a
maximum room temperature of 32°C. The
"Timer-2h" mode is automatically deactivated after a period of 2 hours
and the device returns to the operative
mode previously set. The user can switch to another operative mode at
any time by simply pressing the [Prog] button.
Chrono mode
This operating mode allows the user to configure different temperature
values for each hour of each day of the week. The "Comfort" / "Night"
temperatures and the related time intervals can be thus programmed.
-To activate this function, press the [Prog] button until the "Chrono"
icon is displayed.
- 17 -
Night Antifreeze Timer 2H
7
*The version with Fil-Pilot is available for specific countries.
English
Chrono