Etac R82 Multi Frame Bedienungsanleitung Seite 37

Safety
Signs, symbols and instructions placed on this product must never be covered or removed and must remain present
and clearly legible throughout the entire lifetime of the product. Immediately replace or repair illegible or damaged
signs, symbols and instructions. Contact your local dealer for instructions.
In case of an adverse event occurred in relation to the device, incidents should be reported to your local dealer
and the national competent authority in a timely manner. The local dealer will forward information to manufacturer.
Caregiver
• Read the "User Guide" carefully before use
and keep it for future reference. Incorrect use
of this product may cause serious injury to the
user
• This product contains small parts which could
present a choking hazard if removed from their
intended placing
• Always use the correct lifting techniques and
aids for this purpose
• Never leave the user unattended in this
product. Ensure permanent supervision by a
caregiver
• Repair/replacements must only be made using
new original R82 spare parts and fittings and
carried out in accordance with the guidelines
and service intervals prescribed by the supplier
• Be aware of any MAX mark indications before
adjustment
• Ensure that moving parts does not squeeze or
trap body parts when adjusting them
• Ensure that body parts are not trapped
in openings for mounting of supports/
accessories.
• If there is any doubt as to the continued safe
use of your R82 product or if any parts should
fail, stop using the product immediately and
contact your local dealer as soon as possible
• Always use the product in a moderate pace. Do
not run with the product
• Information regarding frame and seat
combinations including max. load in
combination can be found at: etac.com
• Information about transportation can be found
in the document "Transportation in Motor
Vehicles" supplied with the product
• Information about roadability can be found in
the document "Roadability" supplied with the
product
Environment
• Observe the surface temperature on the
product, before placing an user in it. This goes
especially for users with insensitive skin as they
cannot feel the heat. If the surface temperature
is above 41°C then allow the product to cool
before use
User
• If the user is close to the max. load limit and/
or has a lot of involuntary movements, e.g.
rocking, a larger size with a higher max. load or
a different R82 product should be considered
etac.com
Product
• Carry out all positional adjustments on the
product and accessories and ensure that
all knobs, screws and buckles are securely
fastened before use. Keep all tools out of the
reach of children
• Removable parts without use of tool: wheels
and foot support. The removal will have adverse
effect on the device
• Ensure the stability of the product is
maintained before placing the user in it
• Activate the brakes before placing the user into
the product
• Activate the anti-tips before angling the seat
and back
• Deactivate the anti-tips when forcing kerbs
higher than 100 mm
• We recommend you notify the user before
angling the seat and back
• Ensure the wheels are fully-functional and
secure before use
• The correct tyre pressure is printed on the
tyre casing and listed in the section for tyre
technical data.
• In case of a tyre puncture do not use the
product until remedied
• Ease of access to and maneuverability in,
motor vehicles can be significantly affected
by size of device and turning radius, and the
smaller device and/or device with a shorter
turning radius will generally provide greater
ease of vehicle access and maneuverability to
a forward facing position. In accordance with
ISO 7176-19 Annex D, the product is evaluated
regarding the ability to accommodate vehicle-
anchored pelvic and shoulder belts. The device
receives an overall score of "Good"
• Unoccupied device is suitable for land and air
transport
• Attaching additional loads can adversely affect
stability. Position of points intended to carry
additional loads are specified in the relevant
Mounting Guide referred to under section for
accessories
• Do not expose the gas spring to pressure or
high temperatures. DO NOT puncture
• Inspect the product and all of its accessories
and replace any worn out parts before use
• This product is tested for resistance to ignition
at level non-ignition in accordance with EN
1021-1, EN 1021-2 and ISO 7176-16
• The product might lose its flame resistant
characteristics if using other than original R82:
Cushions
37
EN