Specifications - Makita 1902 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Knob
2-1. Switch trigger
3-1. Lock button / Lock-off button
3-2. Switch trigger
4-1. Socket wrench
4-2. Bolt
5-1. Bolt
5-2. Drum
5-3. Planer blade
5-4. Drum cover
5-5. Adjusting plate
6-1. Inside edge of gauge plate
6-2. Blade edge
6-3. Planer blade
6-4. Adjusting plate
6-5. Screws
6-6. Heel
6-7. Back side of gauge base
6-8. Gauge plate
6-9. Gauge base
7-1. Socket wrench
7-2. Bolt

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Downloaded from www.Manualslib.com
Explanation of general view
8-1. Pan head screw
8-2. Adjusting plate
8-3. Planer blade locating lugs
8-4. Gauge plate
8-5. Heel of adjusting plate
8-6. Set plate
8-7. Inside flank of gauge plate
8-8. Gauge base
8-9. Back side of gauge base
8-10. Mini planer blade
9-1. Mini planer blade
9-2. Groove
9-3. Set plate
9-4. Hex. flange head bolt
9-5. Drum plate
9-6. Drum
9-7. Adjusting plate
10-1. European type (round) chip cover
11-1. Vacuum cleaner
12-1. Chip cover
12-2. Screwdriver
13-1. Nozzle assembly
Model
Planing width
Planing depth
Shiplapping depth
-1
No load speed (min )
Overall length
Net weight
Safety class
) : 84 dB(A)
pA
) : 95 dB(A)
WA
Wear ear protection
manuals search engine
ENE001-1
Vibration
The vibration total value (tri-axial vector sum) determined
ENF002-2
according to EN60745:
Work mode : planing softwood
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
ENG102-3
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
4
14-1. Chip cover screw
14-2. Chip cover
14-3. Hole
15-1. End
15-2. Start
17-1. Blade edge
17-2. Cutting line
18-1. Screw
18-2. Edge fence
22-1. V groove
23-1. Sharpening holder
24-1. Wing nut
24-2. Blade (A)
24-3. Blade (B)
24-4. Side (D)
24-5. Side (C)
26-1. Limit mark
27-1. Chip cover
27-2. Screwdriver
28-1. Brush holder cap
28-2. Screwdriver
1902
82 mm
1 mm
9 mm
16,000
290 mm
2.7 kg
/II
2
) : 5.5 m/s
h
2
ENG222-2
ENG901-1