Specifications - Makita N1923B Betriebsanleitung

ENGLISH
(Original instructions)
1 Knob
2 Switch trigger
3 Lock button/Lock-off button
4 Bolts
5 Drum
6 Planer blade
7 Drum plate
8 Adjusting plate
9 Inside edge of gauge plate
10 Blade edge
11 Screws
12 Heel
13 Back side of gauge base
14 Gauge plate
15 Gauge base
16 Pan head screw

SPECIFICATIONS

Model
Planing width ........................................................ 82 mm
Planing depth ......................................................... 1 mm
Shiplapping depth ................................................ 23 mm
–1
No load speed (min ) .......................................... 17,000
Overall length ..................................................... 293 mm
Net weight ............................................................. 3.1 kg
Safety class ................................................................ /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
6
Explanation of general view
17 Planer blade locating lugs
18 Heel of adjusting plate
19 Set plate
20 Inside flank of gauge plate
21 Mini planer blade
22 Groove
23 Hex. flange head bolt
24 Vacuum cleaner
25 Nozzle assembly
26 Chip cover screw
27 Chip cover
28 Fit the pin on nozzle assembly
into this hole.
29 End
30 Start
31 Cutting line
PLANER SAFETY WARNINGS
N1923B
1.
2.
3.
ENE001-1
4.
5.
ENF002-2
6.
7.
8.
9.
10. Before using the tool on an actual workpiece, let
GEA010-2
11. Make sure the blade is not contacting the work-
12. Wait until the blade attains full speed before cut-
13. Always switch off and wait for the blades to
14. Never stick your finger into the chip chute.
15. Do not leave the tool running. Operate the tool
16. Always change both blades or covers on the
17. Use only Makita blades specified in this manual.
32 Edge fence
33 Screw
34 V groove
35 Sharpening holder
36 Wing nut
37 Blade (A)
38 Blade (B)
39 Side (C)
40 Side (D)
41 Limit mark
42 Chip cover/nozzle
43 Screwdriver
44 Brush holder cap
Wait for the cutter to stop before setting the tool
down. An exposed rotating cutter may engage the
surface leading to possible loss of control and seri-
ous injury.
Hold the power tool by insulated gripping sur-
faces, because the cutter may contact its own
cord. Cutting a "live" wire may make exposed metal
parts of the power tool "live" and could give the oper-
ator an electric shock.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the workpiece by your hand or against the
body leaves it unstable and may lead to loss of con-
trol.
Rags, cloth, cord, string and the like should
never be left around the work area.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Use only sharp blades. Handle the blades very
carefully.
Be sure the blade installation bolts are securely
tightened before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
piece before the switch is turned on.
ting.
come to a complete stop before any adjusting.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
only when hand-held.
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
GEB167-1