Operating Elements And Connections - Monacor JTS UF-10R/12 Bedienungsanleitung

Contents
1 Operating Elements and Connections . . 12
2 Safety Notes . . . . . . . . . . . . . . . . . . . . . . . 13
3 Applications . . . . . . . . . . . . . . . . . . . . . . . 13
3.1 Conformity and approval . . . . . . . . . . . . . . 13
4 Rack Installation . . . . . . . . . . . . . . . . . . . . 13
5 Connecting the Receiver . . . . . . . . . . . . . 14
6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 Basic settings . . . . . . . . . . . . . . . . . . . . . . . 14
6.2 Setting the transmission frequency . . . . . . 15
6.2.1 Setting the frequency manually . . . . . . . . 15
6.2.2 Selecting a frequency from a group . . . . 15
6.2.3 Scan function . . . . . . . . . . . . . . . . . . . . . 15
6.2.4 Storing preferred frequencies
in your own frequency groups . . . . . . . . . 16
6.2.5 REMOTSET
Setting the transmitter to the same
frequency . . . . . . . . . . . . . . . . . . . . . . . . 17
6.3 Adjusting the output level . . . . . . . . . . . . . . 18
6.4 Interference suppression . . . . . . . . . . . . . . 18
6.5 Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7 Specifications . . . . . . . . . . . . . . . . . . . . . . 19
Transmission frequencies . . . . . . . . . . . . . . 36
12
All manuals and user guides at all-guides.com
function
®
All operating elements and connections de -
scribed can be found on the fold-out page 3.
1 Operating Elements
and Connections
1 Receiving antennas
2 Button REMOSET to set the transmitter to
the transmission frequency of the receiver
chap ter 6.2.5
3 LED RF (radio frequency) for the power of the
radio signal received
4 LED AF (audio frequency) for the volume of the
audio signal received
5 Display, the section on the left indicates:
which of the two antennas (1) receives the
more powerful radio signal (A or B); if there
is no reception from a transmitter, x will
appear
if the key lock has been activated
the audio output level adjusted
[Mute, -31 ... -1, Max.]
ID the identification number adjusted for the
REMOSET function (0 ... 255)
the battery status in the transmitter; if there
is no reception from a transmitter or if the
transmitter is muted, the message MUTE
will appear instead of the battery symbol
The section on the right indicates:
the name of the unit, any name may be selected
(10 characters)
G = the group number (1 ...12, U1 ... U6)
CH = the channel number (1 ... 60)
MHz = the receiving frequency
(624.000 ... 694.000 MHz)
6 Button SETUP to call up the setup menu shown
in fig. 1 (keep the button pressed for 2 seconds
until the menu appears on the display) and to
save the setting (press the button briefly)
7 Control knob PUSH / CONTROL
If the menu has been called up:
- turn the knob to select a menu item or to
change a setting.
- press the knob to call up a menu item.
8 Button EXIT to exit the menu or a submenu