Optional Accessories - DeWalt XR LI-ION DCS387 Bersetzt Von Den Originalanweisungen

Downloaded from www.Manualslib.com
WARNING: Use extra caution when
cutting overhead and pay particular
attention to overhead wires that may be
hidden from view. Anticipate the path
of falling branches and debris ahead of
time.
WARNING: Inspect work site for
hidden gas pipes, water pipes, or
electrical wires before making blind
or plunge cuts. Failure to do so may
result in explosion, property damage,
electric shock, and/or serious personal
injury.
FLUSH-TO CUTTING (FIG. 9)
The compact design of the saw motor housing and
spindle housing permits extremely close cutting to
floors, corners and other difficult areas.
POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 10)
The initial step in pocket cutting is to measure the
surface area to be cut and mark clearly with a
pencil, chalk or scriber. Use the appropriate blade
for the application. The blade should be longer than
90 mm (3-1/2") and should extend past the shoe
and the thickness of the workpiece during the cut.
Insert blade in blade clamp.
Next, tip the saw backward until the back edge
of the shoe is resting on the work surface and the
blade clears the work surface (position 1, fig. 10).
Now switch motor on, and allow saw to come up to
speed. Grip saw firmly with both hands and begin
a slow, deliberate upward swing with the handle
of the saw, keeping the bottom of the shoe firmly
in contact with the workpiece (position 2, fig. 10).
Blade will begin to feed into material. Always be
sure blade is completely through material before
continuing with pocket cut.
NOTE: In areas where blade visibility is limited, use
the edge of the saw shoe as a guide. Lines for any
given cut should be extended beyond edge of cut
to be made.
METAL CUTTING (FIG. 11)
Your saw has different metal cutting capacities
depending upon type of blade used and the metal
to be cut. Use a finer blade for ferrous metals
and a coarse blade for non-ferrous materials. In
thin gauge sheet metals it is best to clamp wood
to both sides of sheet. This will ensure a clean cut
without excess vibration or tearing of metal. Always
remember not to force cutting blade as this reduces
blade life and causes costly blade breakage.
NOTE: It is generally recommended that when
cutting metals you should spread a thin film of oil or
other lubricant along the line ahead of the saw cut
for easier operation and longer blade life.
manuals search engine
MAINTENANCE
Your D WALT power tool has been designed to
E
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.

Optional Accessories

WARNING: Since accessories, other
than those offered by D
not been tested with this product, use
of such accessories with this tool could
E NG LI S H
WALT, have
E
39