Conrad 67 23 15 Bedienungsanleitung Seite 2

O P E R A T I N G I N S T R U C T I O N S
Automatic Watch Crown
Item-No. 67 23 15
Intended Use
The product serves as a wristwatch. It displays the time in hours, minutes, seconds as well as
the date and the day of the week.
The automatic watch is supplied with energy by winding the mechanism by means of the crown
or through the rotor of the automatic mechanism.
Any use other than described above is not permitted and can damage the product. There are
also risks involved.
Safety and Care Instructions
Please read through the instructions completely, they contain important
information.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequential
damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions!
The warranty will be void in such cases!
• Unauthorised modifications and/or changes to the product are not permitted.
• The wristwatch may not be exposed to intensive, direct sunlight, extreme temperatures, strong
vibration or heavy mechanical stress. This may damage the watch.
• This product is not a toy and does not belong in the hands of children as they may swallow
small parts. Danger of suffocation!
• Do not leave packing materials unattended. They could become a dangerous toy in the hands
of children. Danger of suffocation!
• If the strap becomes damp or wet, let it dry thoroughly. Wearing the watch with the watchstrap
wet might involve discoloration of the watchstrap and irritation to the skin. Furthermore, this
might reduce the lifetime of the watchstrap.
• Only clean the outside of the wristwatch with a soft, slightly damp cloth or a dry brush. Never
use aggressive cleansing agents or chemical solutions since this might damage the surface of
the housing or impair operation of the watch.
Operation
Setting the time
• Pull the crown of the watch (D) into position 2.
• Turn the crown (D) and thus set the current time.
• Press the button (D) into its normal position 1.
Do not set the time backwards if the date display (A) shows "1" or if the weekday dis-
play (C) shows "MON".
This might damage the clockwork.
Setting the date
• The date is shown in the date display (A). It is a retrograde display, i.e. the hand returns to the
beginning of the scale after it has reached the end of the scale.
• Press the button (B) with a sharp item until the current date is displayed.
Setting the weekdays
• The weekday is shown in the weekday display (C). It is a retrograde display, i.e. the hand
returns to the beginning of the scale after it has reached the end of the scale.
• Press the button (E) with a sharp object until the current weekday is displayed.
Please take note that the date and the weekday should not be set in the time
between 10 p.m. and 2 a.m. as in this time the automatic change of date and
weekday is carried out by the mechanics of the watch.
If the clock changes the date/weekday at 12 o' clock noon, set the time 12 hours
ahead. Set the correct date again if necessary.
Winding up the movement
www.conrad.com
• The automatic movement winds itself automatically on your wrist when you wear the watch.
However, the watch stops working when you do not wear it over a longer period of time.
• The watch can also be wound by turning the crown (D) (leave it in position 1) clockwise. Do
Version 02/11
not wind the watch up too far as it can be damaged.
• If the watch does not start again immediately, shake it briefly with a jerk to give it the necessary
start impulse.
Water and Shock Resistance
This watch is designed for normal use only. It must not be exposed to extreme shocks and
impacts. This might damage the clockwork.
The watch is constructed in such a manner that contact with water as it arises in day-to-day life
(washing hands, water spray, rain drops, etc.), has no adverse effect.
The watch is not suitable for swimming, showering or diving. Do not immerse the watch
in water. Leave the crown (D) in normal position and do not turn it when the watch is wet.
Otherwise, water might get into the watch.
Accuracy
The precision of the automatic watch should be checked after a running-in time of approx. one
month.
If you recognise greater deviations from the actual time, present the watch to a watchmaker who
can easily set the precision.
Technical Data
Reserve of runtime:
Bearing jewels:
Water tightness:
© Copyright 2011 by Conrad Electronic SE.
38-40h
33
3 ATM
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.