Maintenance; Optional Accessories - Makita LC1230 Betriebsanleitung

The allowable cutting dimensions are reduced when a
wooden block is used. Use a wooden block whose
dimensions are equivalent to the maximum allowable cut-
ting dimensions minus the dimensions of the workpiece
to be cut. This will further minimize the shortening of the
saw blade life.
Cutting rectangles (Fig. 16)
Secure the workpiece in the vise as shown in Fig. J, and
proceed to cut it.
CAUTION:
• Do NOT cut the workpiece as shown in Fig. K since
this may cause it to be ejected from the vise, possibly
resulting in injury.
Carrying tool (Fig. 17)
Fold down the tool head to the position where you can
attach the chain to the hook on the handle. Grasp the
carrying grip when carrying the tool.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing saw blade
Continuing to use a dull and worn blade may cause
motor overload and decreased cutting efficiency.
Replace with a new blade as soon as it is no longer effec-
tive.
Replacing carbon brushes (Figs. 18 & 19)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
After use
After use, wipe off chips and dust adhering to the tool
with a cloth or the like. Keep the blade guard clean
according to the directions in the previously covered sec-
tion titled "Blade guard". Lubricate the sliding portions
with machine oil to prevent rust.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
12
• Carbide-tipped saw blade
(Refer to our website or contact your local Makita
dealer for the correct saw blades to be used for the
material to be cut.)
• Safety goggle
• Socket wrench
• Lock-off button (Switch button)
NOTE
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN62841-3-10:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
NOTE:
• The declared noise emission value(s) has been mea-
sured in accordance with a standard test method and
may be used for comparing one tool with another.
• The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
WARNING:
• Wear ear protection.
• The noise emission during actual use of the power
tool can differ from the declared value(s) depend-
ing on the ways in which the tool is used especially
what kind of workpiece is processed.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of expo-
sure in the actual conditions of use (taking account
of all parts of the operating cycle such as the times
when the tool is switched off and when it is running
idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN62841-3-10:
Vibration emission (
Uncertainty (K): 1.5 m/s
NOTE:
• The declared vibration total value(s) has been mea-
sured in accordance with a standard test method and
may be used for comparing one tool with another.
• The declared vibration total value(s) may also be used
in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared value(s)
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of expo-
sure in the actual conditions of use (taking account
of all parts of the operating cycle such as the times
when the tool is switched off and when it is running
idle in addition to the trigger time).
ENG905-1
): 107 dB (A)
pA
): 115 dB (A)
WA
ENG907-1
ENG900-1
2
): 3.0 m/s
a
h
2
ENG901-2