Initial Operation; Unpacking The Appliance - Clatronic CL 3227 Bedienungsanleitung

Instructions for Use
CAUTION:
Before the device is put into operation, e.g. before being
used for the fi rst time, whenever it is transported or after
being moved, it should be placed in a horizontal position
for at least 3 hours.
NOTE:
• The fl exible exhaust air hose can be extended from 50 to
150 cm during installation. This length has been especially
designed for the particular features of the air-conditioner.
You should not use any extension or replace the hose with
another one, as this may result in malfunctions. The air
must be allowed to fl ow freely out of the device, as any
blockage may cause it to overheat. Please ensure that the
exhaust air hose is not buckled or bent.
• Close the windows and doors so that no air can enter
the room from outside. The device will then work more
effectively.
• Please ensure that the air can be drawn in and can fl ow
out unhindered. Remove any mobile sources of heat from
the room if necessary.
NOTE:
Some buttons are to be found both on the device and on the
remote control. Buttons with the same designation have the
same function.
CAUTION:
Do not move the device, as otherwise this might cause
the water to leak out and damage the fl oor, carpet or
device.
Never use the air-conditioner without protective fi lters.

Unpacking the appliance

• Remove the appliance from the box and all the enclosed
accessories.
• Do not through the packaging away, but keep it together with
the inner packing and the warranty documents for the whole
life of the warranty.
• Place the appliance on smooth, level and stable work
surface.
• Do not insert the appliance plug without installing the
necessary attachments.
Installation
Installing the Exhaust Air Hose
• Place the connection ring (11) over the exhaust air hose
(10). Turn the connection ring at least fi ve times in a clockwi-
se direction until it is tight. Check that it cannot be pulled off.
• Push the assembled exhaust air hose from right to left
over the hose connection (9) on the back. Guide it into the
holders until it locks in place. In order to release the hose
again, press in the right-hand retainer and push the hose to
the right out of the holder.
05-CL 3227.indd 19 05-CL 3227.indd 19
NOTE:
If the device is in „cooling" mode the end of the exhaust air
hose has to be led out of the air-conditioned room.
Mains Lead Take-up
Unwind the mains lead from the cable holder on the rear of the
device. After using the device, please wind up the lead again.

Initial Operation

• Only connect the machine to a properly installed safety
socket, 230 V/50 Hz.
• Make sure that the degree of protection of the socket to
which the device is connected is of at least 10 ampere!
• Place the device on any heat-resistant fl at surface. Ensure
that air can enter and leave unhindered.
• The distance from the air inlet grille (5/7) to the nearest wall
should be at least 20 cm. The distance from the air outlet
grille (2) to the nearest wall should be more than 1m.
Switching on/off
1. As soon as you have inserted the plug the mains control
lamp (J) lights up in red and indicates that the device is
connected to the mains.
2. Press the „ " button (J) (13 on the remote control) to switch
the device on - the control lamp lights up in green. An
acoustic signal is heard and the digital display (E) shows
22°C. Please wait until the device has begun operation. The
device switches to the highest speed and the „cooling" mode
(the „ " control lamp lights up in red and the
„ " control lamp in green). The air outlet (2) opens. After a
few seconds the device switches on automatically.
Mode of Operation
Press the „ " button (H/14) to switch the mode of operation
between "cooling" (green), „dehumidifi er" (orange) and "ventila-
tor" (no lamp).
NOTE:
Changing the Mode of Operation
When the mode of operation is changed the compressor
remains switched off for approximately 6 minutes until the
pressure in the refrigeration circuit has eased.
Then the compressor switches on again automatically.
Cooling
• If you would like to change the room temperature using the
„cooling" mode of operation, press the „ " or „ " button
(D/F). The digital display (E) shows the temperature (min.
18°C – max. 32°C). The temperature increases or reduces
by 1°C with each press of the button.
• By repeatedly pressing the „ " button (18) on the remote
control you can switch from 18, 19, 20.....32; from there it
returns to 18, 19 etc.
• The device cools the room down to the set temperature,
which it then maintains. If the set temperature is above the
19
11.12.2007 10:09:08 Uhr 11.12.2007 10:09:08 Uhr