Unpacking The Appliance; Overview Of The Components; Initial Operation; Delivery Scope - Clatronic CL 3672 Bedienungsanleitung

Handling Batteries
WARNING:
• Do not expose batteries to excessive heat such as sunlight, fire or
similar. There is a risk of explosion!
• Batteries are not toys. Keep away from children.
• Do not open batteries by force.
• Avoid contact with metal objects (rings, nails, screws, etc.). There is
a risk of short circuit!
• A short circuit could cause the battery to heat up excessively or even
to catch fire, resulting in injuries.
• For your own safety, cover the battery terminals with adhesive tape
during transport.
• In case of battery leakage, make sure not to rub the liquid into your
eyes or mucous membranes. In case of contact, wash your hands
and rinse your eyes with clear water. Seek medical attention if any
discomfort persists.
CAUTION:
• When not using the remote control for a long period of time, remove
the batteries in order to prevent "leakage" of battery acid.
• Different battery types or new and used batteries must not be used
together.
• Do not dispose of batteries along with domestic waste. Return used
batteries to the relevant collection facilities or your retailer.

Overview of the Components

1 Air inlet on the side of the appliance (Filter)
2 Control panel
3 Air outlet (fins)
4 Mains cable
5 Exhaust pipe connector
6 Exhaust pipe adapter
7 Flexible exhaust pipe
8 Water outlet
9 Rear side air inlet (Filter)
10 Control lamp W.F
11 Control lamp HIGH
12 Control lamp LOW
13 Control lamp TIMER
14 Display
15 Control lamp COOL
16 Control lamp DEHUM
17 Control lamp FAN
18 TIMER button
19 SPEED button
20 MODE button
21 IR receiver for remote control
22 TEMP − button
23 TEMP + button
24 POWER button

Delivery Scope

1 Air conditioning appliance
1 Remote control
2 Batteries
1 Flexible exhaust pipe
1 Exhaust pipe adapter (Connection on the appliance)
1 Window kit, 2-piece
1 Adapter for the window exhaust kit
1 Water hose, Ø 16 mm
2 Rubber caps (spares)
2 Plugs (spares)
30
CL3672_IM_new2

Unpacking the Appliance

1. Remove the appliance from its packaging.
2. Remove all the packaging material such as plastic bags, filler material,
cable ties and cardboard packaging.
3. Check that all parts are supplied in the package.
Notes on Use
CAUTION: Important for initial operation or after transport!
Before initial operation, the appliance must stay in an upright position for
at least 3 hours in order for the cooling agent to sink. The compressor
will be damaged otherwise.
CAUTION:
• When you interrupt the operation with the POWER
at least 3 minutes before switching the appliance on again.
• If you want to move the appliance to another location, first empty the
water tank!
NOTE:
You will find all operating buttons on both the appliance and the remote
control. Same buttons represent the same functions.
• The appliance operates most effectively with a room size up to 70 m³.
• The flexible exhaust hose and the adapter (6) have been manufactured
especially for this appliance. In order to avoid incorrect operation, do not
replace the pipe with another pipe.
• The exhaust pipe can be extended up to 150 cm. Do not use any
extension.
• Ensure free airflow. Make sure not to kink or bend the exhaust pipe. Any
blockage can cause the appliance to overheat.
• Close all windows and doors in order to prevent outside air from
entering the room and thus allowing a more effective operation of the
appliance.

Initial Operation

Location
• When installing the appliance, make sure to keep a distance of at least
30 cm between the appliance and any walls or other objects.
• The surface must be flat and dry.
Assembly of Exhaust Pipe
NOTE:
For sliding windows, you may use the window kit provided and install it
in a vertical or horizontal position. Adjust the length of the seal plate as
desired.
1. Turn the adapter (6) to one end of the exhaust pipe.
2. Connect the exhaust pipe to the appliance using the exhaust pipe
connector. Set the adapter first on the left side. Press the adapter on
the right side down into the linkage.
3. Extend the pipe to the desired length.
4. Stick the open end of the pipe into a window.
5. Close the window as far as possible. Also lower any external roller
blinds, if present, to the end of the pipe.
Remote Control
1. Open the battery compartment cover on the back of the remote
control.
2. Insert 2 batteries of type R03 "AAA" 1.5 V, observing the correct polarity
(see markings on the bottom of the compartment)!
3. Close the battery compartment cover.
button, wait for
14.12.2016