Your Device At A Glance; Using For The First Time - CMi C-AMBS-7.2 Set Originalbetriebsanleitung

• Inform yourself about the surface to be
sanded and any dusts and vapours that may
be generated. If in doubt, do not breath in
even small amounts of the generated dusts
and vapours. When sanding certain surfaces
(various metals, minerals or woods as well as
weather protecting paints) damaging/poisonous
dusts may be generated which can cause allergic
reactions or serious illness. Do not breathe these
dusts and vapours in and avoid all contact. Mate-
rials containing asbestos may only be processed
by specialists.
• Never use the power too with a damaged
cable. Do not touch a damaged cable and pull
out the power plug. Damaged cables increase
the risk of electric shock.
• Prevent overheating of the device and the
work piece. Excess heat may damage the tool
and the device.
• Shortly after being used, the tool may be very
hot. Allow a hot tool to cool down. Touching a
hot tool may cause burns.
• Never clean a hot tool with flammable liq-
uids. There is a risk of fire and explosion.
• Keep the handles dry and free of grease.
Slippery handles can lead to accidents.
• Always comply with the all applicable domes-
tic and international safety, health, and work-
ing regulations. Inform yourself before you start
work about the regulations that apply at the site
of the device.
• Remember that moving parts may also be
located behind ventilation and venting slots.
• Symbols appearing on your product may not be
removed or covered. Signs on the product that
are no longer legible must be replaced immedi-
ately.
Read and observe the instructions for use
before using the product for the first time.
Risks caused by vibrations
CAUTION! Risk of injury due to vibra-
tions! Vibrations may, in particular for per-
sons with circulation problems, cause dam-
age to blood vessels and/or nerves.
If you notice any of the following symptoms,
stop working immediately and consult a
doctor. Numbness of body parts, loss of
sense of feeling, itching, pins and needles,
pain, changes in skin colour.
The vibration values specified in the technical data
represent the main uses of the device. The actual
existing vibrations during use may deviate from these
as a result of the following factors:
• Incorrect use of the product;
• Unsuitable tools inserted;
• Unsuitable material;
• Insufficient maintenance.
You can reduce the risks considerably by following
the tips below:
– Maintain the device in accordance with the
instructions in the operating instructions.
– Avoid working at low temperatures.
– When it is cold, make sure your body and your
hands, in particular, are kept warm.
– Take regular breaks and move your hands at the
same time to promote circulation.
Remaining risks
There will still be residual risks even when the device
is used according to the instructions and under obser-
vation of all of the safety notes in this set of operating
instructions:
• Touching the tool in the uncovered section.
• Reaching into the operating tool.
• Kickback from work pieces and work piece parts.
Personal protective clothing
Wear goggles when working with the device.
When working with tools that cause consid-
erable dust, wear a dust protection mask.
If you have long hair, cover or wear a hair
net.
Do not wear protective gloves when working
with the device.

Your device at a glance

Note: The actual appearance of your prod-
uct may differ from the illustrations.
► P. 3, item 1
1. Control lights for speed
2. Buttons for speed control
3. Control lights for remaining battery capacity
4. On/Off switch
5. Locking button
6. Screw cap
7. Tool holder
8. Socket for charging device
Scope of delivery
• Operating manual
• Axial grinder
• Protective hood
• Power supply
• Accessories box
• Case
• Installation wrench

Using for the first time

Charging the battery pack
WARNING! Risk of injury! Comply with all
safety instructions when handling recharge-
able devices.
NOTICE! Risk of damage to the unit! Do
not allow the battery pack to deep dis-
charge.
NOTICE! Risk of damage to the unit! Do
not press the On/Off switch after the device
has deactivated automatically.
GB
35