Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
WARNING: The COMMAND must be connected to the mains with a differential line cut-off switch according to
the regulations in force. Correct operation of the command is assured only for the proper motor for which
it has been manufactured. Improper use relieves the manufacturer from each responsibility.
POWER SUPPLY
PROTECTION
DIMENSIONS
CONTAINER
9.
ALLOWED / NOT ALLOWED FUELS
Allowed fuels are logs. Use exclusively dry logs (max. content of water 20%). Maximum 3 logs should be loaded. The
pieces of wood should have a length of ca. 30 cm and a maximum circumference of 30 cm. Compressed not worked-
out wood briquettes must be used carefully to avoid overheating that may damage the device, since these
have a very high calorific value.
The wood used as fuel must have a humidity content lower than the 20% and must be stored in a dry place. Humid
wood tends to burn less easily, since it is necessary a greater quantity of energy to let the existing water evaporate.
Moreover, humid content involves the disadvantage that, when temperature decreases, the water condensates earlier
in the hearth and therefore in the stack causing a remarkable deposit of soot with following possible risk of fire of the
same.
Fresh wood contains about 60% of H
It is necessary to place this wood in a dry and ventilated place (for example under a roofing) for at least two years
before using it.
Besides others, it is not possible to burn: carbon, cuttings, waste of bark and panels, humid wood or wood
treated with paints, plastic materials; in this case, the warranty on the device becomes void.
Paper and cardboard must be used only to light the fire. The combustion of waste is forbidden and would even
damage the device.
WARNING: The continuous and protracted use of aromatic wood (eucalyptus, myrtle etc.) quickly damages the cast
iron parts (cleavage) of the product.
10. LIGHTING
After the first ignition you can smell bad odors (owing to the drying of the glue used in the garnitures or of the paint)
which disappear after a brief using of the appliance. A good ventilation of the room should always be guaranteed.
To light the fire, it is suggested to use small wood pieces together with paper or other traded lighting means.
It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.
The openings for air (primary and secondary) must be opened simultaneously, just a little.
You should place a little quantity of fuel and also open the primary air register (left lever completely pulled out) and
that of secondary air (right lever completely pushed).
When wood starts to burn, it is possible to feed it again by opening slowly the door, in order to avoid leaks of smoke,
and close the primary air register (completely pushed) and control the combustion through the secondary air register
according to the provisions of CHAP.11.
Please always be present during this phase.
Never overload the device (see technical table - max. quantity of loadable fuel / Hourly consumption).
Too much fuel and too much air for combustion can cause overheating and therefore damage the same.
Never switch on the device when there are combustible gases in the room.
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the
following information:
•
the construction materials of the involved product are not homogenous, in fact cast iron parts do exist at the
same time, in steel, in refractory material and in majolica;
•
the temperature to which the body of the product is subject is not homogeneous: from area to area, variable
temperatures within the range of 300 ° C - 500 ° C ar e detected;
•
during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to
cycles of intense use or of absolute standstill when season changes;
•
the new device, before being considered seasoned has to be subject to many start cycles to allow all materials
and paints to complete the various elastic stresses;
•
in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress,
as well as of paint that is still wet. This paint, although during the manufacture it is backed at 250 ° C for some
26
TECHNICAL FEATURES
230 V~ +15 – 10% 50/60 Hz
Delayed glass fuse 5x20 2A (T)
145 x 67 x 30 mm
Self-extinguishing ABS IP40 V0
TM
Thermostat
O, therefore it is not suitable to be burnt.
2
Monoblocco Ghisa 750
6099751 Rev.04 – EN
Werbung
Inhaltsverzeichnis
