Troubleshooting & Tips - Scandomestic SFO 2203 W Bedienungsanleitung

Step 5:
Install the adjust screw into the base
Step 6:
Install the dishwasher in aperture, but not full, as figure, adjust
screw, let its bottom align aperture's base, then push dishwasher
full.
Adjust screw
TROUBLESHOOTING TIPS
Before Calling For Service
Reviewing the charts on the following pages may save you from
calling for service.
Dishwasher doesn't start
• Fuse blown, or the circuit breaker tripped.
• Replace fuse or reset circuit breaker. Remove any other ap-
pliances sharing the same circuit with the dishwasher.
Power supply is not turned on.
• Make sure the dishwasher is turned on and the door is clo-
sed securely.
• Make sure the power cord is properly plugged into the wall
socket.
• Door of dishwasher not properly closed.
• Make sure to close the door property and latch it.
Water not pumped from dishwasher
• Kink in drain hose
• Check drain hose.
Filter clogged.
• Check the coarse filter. (see section titled " Internal Care ")
Kitchen sink clogged.
• Check the kitchen sink to make sure it is draining well. If the
problem is the kitchen sink that is not draining, you may
need a plumber rather than a serviceman for dishwashers.
Suds in the tub
• Improper detergent
• Use only the special dishwasher detergent to avoid suds. If
this occurred, open the dishwasher and let suds evaporate.
• Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then Start any wash cycle to drain out the wa-
ter. Repeat if necessary.
Spilled rinse-aid.
• Always wipe up rinse-aid spills immediately.
Stained tub interior
• Detergent with colourant may have been used.
• Make sure that the detergent has no colourant.
White film on inside surface
• Hard water minerals.
• To clean the interior, use a damp sponge with dishwasher
detergent and wear rubber gloves. Never use any other
cleaner than dishwasher detergent for the risk of foaming or
suds.
There are rust stains on cutlery
• The affected items are not corrosion resistant.
• Avoid washing items that are not corrosion resistant in the
dishwasher.
• A program was not run after dishwasher salt was added.
Traces of salt have gotten into the wash cycle.
• Always run the quick wash program. without any crockery in
the dishwasher and without selecting the Turbo function (if
present), after adding dishwasher salt.
The lid of the softer is loose.
• Check the lip. Ensure the fix is fine.
Knocking noise in the wash cabinet
• The spray arm is knocking against an item in a basket.
• Interrupt the program, and rearrange the items which are
obstructing the spray arm.
Rattling noise in the wash cabinet
• Item of crockery are loose in the wash cabinet.
• Interrupt the program, and rearrange the items of crockery.
Knocking noise in the water pipes
• This may be caused by on-site installation or the cross-
section of the piping.
• This has no influence on the dishwasher function. If in doubt,
contact a qualified plumber.
The dishes are not clean
• The dishes were not loaded correctly.
See PART 2 "Preparing And Loading Dishes".
• The programme was not powerful enough.
• Select a more intensive programme.
• Not enough detergent was dispensed.
• Use more detergent, or change your detergent.
Item are blocking the path of spray arms.
• Rearrange the items so that the spray can rotate freely.
The filter combination in the base of wash cabinet is not clean
or is not correctly fitted.
• This may cause the spray arm jets to get blocked.
• Clean and/or fit the filter correctly. Clean the spray arm jets.