Important Safety Instructions; Specifications - Anker A2509 Bedienungsanleitung

EN
LED Indicator Status
Solid blue for 3 seconds, then off Connected to power
Solid blue Charging mobile device
Flashing blue Metal or abnormal objects detected
Under-voltage or over-voltage protection, indicating that
Flashing green
you need to change the adapter
• You cannot charge your device wirelessly in these scenarios:
using a case with a magnetic/iron plate;
T
O
using a case with a pop socket;
O
using an ultra-thick (> 5 mm) protective phone case.
O
• Do not use an adapter with an output of 5V or less.
• Do not place any foreign objects between your device and the wireless charger's
surface, including metal pads on a car mount, credit cards, door keys, coins, metal,
or NFC cards, which will make wireless charging fail or cause overheating.
• Wireless chargers make charging more convenient than wired chargers, but confined
by current wireless technology, their charging speed is slower than that of wired
chargers.
• High temperatures will reduce charging speed and restrict power, which is a
phenomenon common to all wireless chargers. It is recommended that you charge
your device in environments with temperatures below 25°C / 77°F.
• Both the protective phone case and the position of your device on the wireless
charger will affect the charging speed. The farther it is placed from the center of the
wireless charger, the slower the charging speed will be.

Important Safety Instructions

• Avoid dropping.
• Do not disassemble.
• Do not expose to liquids.
• For the safest and fastest charge, use original or certified cables.
• This product is suitable for moderate climates only.
• The maximum ambient temperature during use of this product must not exceed 40°C.
• Open flame sources, such as candles, must not be placed on this product.
• Only use a dry cloth or brush to clean this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
01
any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures: (1) Reorient or relocate the
receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio / TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20 cm
between the radiator & your body.
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1 800 988 7973
Product Name: PowerWave Sense Pad Alloy
Model: A2509
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
IC Statement
This device complies with RSS-216 of Industry Canada. Operation is subject to the condition that
this device does not cause harmful interference.
This device complies with Industry Canada license-exempt RSS standard(s) Operation is subject
to the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the
device.

Specifications

Input 9V 2A，12V
Wireless Output 11W Max
Size 90 x 90 x 13 mm / 3.5 x 3.5 x 0.5 mm
Weight 105 g / 3.7 oz
1.5A，15V 1.2A
02