Important Safety Instructions - Anker 535 Bedienungsanleitung

IMPORTANT SAFETY INSTRUCTIONS

WARNING - When using this product, basic precautions should always be followed, including the following:
Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the product is used near children.
• Do not put fingers or hands into the product.
• Do not expose the product to rain or snow.
• Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire
or injury to persons.
To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the
product.
• Do not use the product in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to
persons.
• Do not use the product that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior
resulting in fire, explosion or risk of injury.
Do not operate the product with a damaged cord or plug, or a damaged output cable.
• Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect
reassembly may result in a risk of fire or electric shock
• Do not expose to fire or high temperatures. Exposure to fire or temperatures above 130°C may cause explosion.
To reduce the risk of electric shock, unplug the power pack form the outlet before attempting any instructed
servicing.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that
the safety of the product is maintained.
• When charging a device, the product may feel warm, this is a normal operating condition and should not be cause
for concern.
When charging the internal battery, work in a well ventilated area and do not restrict ventilation in any way.
• Do not clean the product with harmful chemicals or detergents.
• Misuse, dropping or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems
separate from each other.
CAUTION: Risk of explosion if the battery is replaced by an incorrect type.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an
explosion;
• Leaving a battery in an extremely high temperature environment can result in an explosion or leakage of flammable
liquid or gas;
• A battery subjected to extremely low air pressure may cause an explosion or leakage of flammable liquid or gas;
Unplug the AC power cable to disconnect from line voltage.
Storage and Maintenance instructions
1. Please store the product between 32°F-104°F (0°C-40°C). Avoid exposing the product to rain or using the
product in a humid environment.
2. To preserve battery lifespan, please discharge the battery to 30% and recharge it to 60% every three months.
3. Please keep the product laid flat during use, when charging, and during storage.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
07
(4) Consult the dealer or an experienced radio / TV technician for help.
The following importer is the responsible party.
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973
IC Statement
This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1)
This device may not cause interference, and (2) This device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
This digital apparatus complies with CAN ICES-003(B)/NMB-003(B).
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A1751 is in compliance with Directives 2014/35/
EU & 2014/30/EU & 2011/65/EU. The full text of the EU declaration of conformity is available at the following
internet address:
https://www.anker.com
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A1751 is in compliance with Electrical Equipment
(Safety) Regulations 2016 & Electromagnetic Compatibility Regulations 2016 & The Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of
conformity is available at the following internet address:
https://www.anker.com.
Anker Innovations Limited | Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, HongKong
The following importer is the responsible party（contract for EU and UK matters）
Anker Innovations Deutschland GmbH | Georg-Muche-Strasse 3, 80807 Munich, Germany
Anker Technology (UK) Limited | GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom
08