Functional Description - Makita VC1310LX1 Betriebsanleitung

35. Never handle plug cord or cleaner with wet hands.
36. Use extreme caution when cleaning on stairs.
KEEP FOR FUTURE REFERENCE
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
This cleaner is intended for commercial use, for example
in hotels, schools, hospitals, factories, shops, offices and
rental businesses.

FUNCTIONAL DESCRIPTION

WARNING:
• Before plugging the cleaner, always make sure that
the cleaner is switched off. Plugging the cleaner with
the switch on may cause an unexpected start resulting
in serious personal injury.
Switch action (Fig. 1)
To start the cleaner, rotate the switch lever to the "I" side.
To stop it, rotate the switch lever to the "O" side.
The suction power can be adjusted according to your
work need. (Fig. 2)
Suction power can be increased by turning the suction
force adjusting knob from the
symbol.
Connecting electric power tools
WARNING:
• Observe the maximum connected loads for the
appliance socket (Refer to the SPECIFICATIONS.)
• Make sure that both the cleaner and the electric power
tool are switched off before connecting or
disconnecting. Connecting the power tool to the
cleaner with both of them being switched on may cause
unexpected and sudden start resulting serious
personal injury.
When connecting a grounded tool, insert a plug with a
grounding plate to the socket of the cleaner. (Fig. 3)
CAUTION:
• Never connect an electric power tool with an input
power exceeding that specified in the
"SPECIFICATIONS" to the socket of the cleaner by
turning the suction force adjusting knob. Connecting
the electric power tool exceeding the specified input
power may cause overheat and damage to the cleaner.
Refer to the specifications to avoid this.
The cleaner can be connected to an electric power tool up
to input power shown in the "SPECIFICATIONS".
To connect an electric power tool, open the cap and insert
the power tool plug into the socket of the cleaner.
Rotate the switch lever to the "AUTO" position. (Fig. 2)
Move the suction force adjusting knob to the position
suitable for the input power of the electric power tool you
intend to use. Refer to the SPECIFICATIONS for the
relation between suction force adjusting knob and the
electric power tool input power.
10
symbol to the
Switching on and off of the connected electric power tool
simultaneously brings the cleaner switching on and off
action. The cleaner still works for a few seconds even
after the electric power tool is switched off.
After use, disconnect the power tool from the socket of
cleaner.
Switch off the cleaner after use.
Auto-suction stop during suction
operation
WARNING:
• Do not use for a long time while the float is at work.
Using the cleaner with its float at work for a long time
can cause overheat, resulting in the cleaner
deformation.
• Do not pick up foam or soapy liquid. Picking up
foam or soapy liquid can cause foam to come out of air
exit before the float works. Continuing to using in this
condition may cause an electric shock and breakage of
the cleaner.
The cleaner has a float mechanism that prevents water
from immersing into the motor when picking up more than
a certain amount of water.
When the tank is full and the cleaner no longer picks up
water, switch off the cleaner and empty the tank.
Installing the holder (Fig. 4)
When connecting an electric power tool, secure the power
supply cord and hose using the holders at a 70 cm -
80 cm distance among the holders that are provided with
the cleaner so that the hose is not entangled by the power
supply cord.
Usage of base hook
CAUTION:
• Be careful not to pinch your fingers when closing
the base hook. Failure to do so may cause personal
injury.
NOTE:
• Do not apply an excessive force on the base hook. The
excessive force on the base hook may damage the
base hook. Close the base hook when not in use.
Opening the base hook allows the following usage.
1. Storing the power supply cord
NOTE:
• Do not use the cleaner or a connected electric
power tool with a power supply cord wound on the
base hook. Using the cleaner or the connected electric
power tool with power supply cord may cause damage
the power supply cord. (Fig. 5)
2. Storing the front cuffs
Front cuffs 22, 24 and 38 can be stored (up to two at a
time.) (Fig. 6)
3. Storing the hose (Fig. 7)
4. Resting a reasonable size of electric power tool
for the base hook, such as circular saw. (Fig. 8)