Specifications - Makita DJS130RFE Betriebsanleitung

ENGLISH
(Original instructions)
1 Red part
2 Button
3 Battery cartridge
4 Trigger-lock button
5 Switch trigger
6 Cutting head
7 Screws
8 Hex wrench
9 Side blade L
10 Center blade

SPECIFICATIONS

Model
Max. cutting capacities
Steel up to 400 N/mm
Stainless Steel up to 600 N/mm
Strokes per minute (min
Overall length ..................................................... 350 mm
Net weight .............................................................. 2.2 kg
Rated voltage ...................................................D.C. 18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
CORDLESS SHEAR SAFETY WARNINGS
1. Hold the tool firmly.
2. Secure the workpiece firmly.
3. Keep hands away from moving parts.
4. Edges and chips of the workpiece are sharp.
Wear gloves. It is also recommended that you
put on thickly bottomed shoes to prevent injury.
5. Do not put the tool on the chips of the work-
piece. Otherwise it can cause damage and trou-
ble on the tool.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
8. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
Explanation of general view
11 Side blade R
12 Sleeve
13 Tighten
14 Hook
15 Side blade
16 Side blade surface
17 Workpiece
18 Lubricate
19 Limit mark
20 Holder
2
........................1.3 mm (18 ga.)
2
.........1.0 mm (20 ga.)
–1
) ...................................... 2,800
9. Avoid cutting electrical wires. It can cause seri-
ous accident by electric shock.
BJS130
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
ENE037-1
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
GEA010-1
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
GEB067-1
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
21 Hex socket head bolt
22 Barrel
23 Front cover
24 Spring
25 Arm
26 Recessed part
27 Carbon brush cap
28 Hole
ENC007-6
5