Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Z. XLR OUTPUTS - Studio quality, true electronically
balanced outputs that provide the ability to send
Channel 1 and 2 separately or together for custom
mixing. All 3 XLR outputs include onboard tone
shaping and the effects loop signal, BUT only the
CH 1 + 2 output includes Reverb. Output level is
controlled by GAIN {H}, pin wiring is "American
Standard": 1=Ground, 2=(+), 3=(–).
GROUND / LIFT - Disconnects the ground
connection (pin-1) from all 3 XLR outputs, which may
reduce hum noise due a ground loop (non-standard
XLR wiring somewhere in the signal path). Normally
leave this switch out.
GROUNDED (normal)
Lifting the ground connection will not solve hum noise
due to bad cables, poor connections, miswired A/C
outlets, nearby fluorescent lighting (especially with
single-coil pickups) or a cell phone close to your
instrument.
AA. TWEETER LEVEL CONTROL -
Controls the volume of the high-
frequency
tweeter.
start by setting this control to the
"12 o'clock" position, then adjust
as desired.
such as violins, cellos and
upright basses may sound best
with the tweeter off (LEVEL CONTROL fully counter-
clockwise). The front panel TREBLE knob controls the
TYPE:
PART NUMBER:
POWER REQUIREMENT:
POWER OUTPUT:
INPUT IMPEDANCES
FUSES:
SPEAKERS:
DIMENSIONS
WEIGHT:
Downloaded from
www.Manualslib.com
GROUND LIFTED
Normally,
Some instruments
PR 628
4460000010 (120V, 60Hz) US
4460003010 (240V, 50Hz) AUS
4460005010 (220V, 50Hz) ARG
4460007010 (100V, 50Hz) JPN
360 W
200 W RMS into 4 Ω @ 0.1%THD
INSTRUMENT: 3.9M Ω
STEREO: 1M Ω
AUX: 1M Ω
F8A 250V for 100V–120V versions
F4A 250V for 220V–240V versions
One 8Ω, 200W, 12" stamped frame woofer (P/N 0067084000 )
One 16Ω, 25W, supertweeter (crossover 4kHz) (P/N 0067254000)
HEIGHT: 25 in
WIDTH: 15 in
DEPTH: 14 in
51 lb
Product specifications are subject to change without notice.
s s w
w r r s s o
manuals search engine
R R
e e
a a
r r
P P
R R
e e
a a
r r
P P
frequency range of the tweeter and can be used as a
"high-end pad."
BB. EXTENSION SPEAKER OUTPUTS - The California
Blonde II amplifier features both Speakon
advantage of its superior power transfer efficiency and
locking connector. Both jacks are full range and wired
in parallel.
•
Connect speakers with a total impedance load of 8-
ohms minimum to prevent damage to your
equipment (one 8-ohm speaker or two 16-ohm
speakers are acceptable).
•
ONLY connect speakers to these outputs.
•
ALWAYS switch the amplifier OFF before connecting
or disconnecting speakers.
•
ONLY use unshielded speaker cable of 18 gauge or
heavier (such as 16 or 14 gauge) for speaker
connections. Shielded instrument cable WILL NOT
work and may damage your equipment.
(63.5 cm)
(38.1 cm)
(35.6 cm)
(23.1 kg)
o u
u n
n d
d . . c
c o
o m
m
a a
n n
e e
l l
—continued
a a
n n
e e
l l
1/4" phone speaker output jacks
to provide flexibility in making
your
extension
connections. Use the Speakon
jack whenever possible to take
S S
p p
e e
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
S S
p p
e e
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
4460001010 (110V, 60Hz) TW
4460004010 (230V, 50Hz) UK
4460006010 (230V, 50Hz) EUR
4460009010 (220V, 60Hz) ROK
150W RMS into 8 Ω @ < 0.02% THD
9
®
and
speaker
®
Werbung
