Before Starting The Equipment; General Information - EINHELL TC-MS 2112 Originalbetriebsanleitung

Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.

5.1 General information

•
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment's moving parts run
smoothly.
5.2 Setting up the saw (Fig. 3)
The workpiece supports must be inserted and
tightened using a hex key (C).
5.3 Adjusting the saw (Fig. 1/2)
•
To adjust the turntable (8), loosen the knurled
screw (10) by approx. 2 turns, which frees the
turntable.
•
The turntable has locking points at angles
of 0°, 5°, 10°, 15°, 22,5°, 30°, 35°, 40°, 45°.
Once the turntable is engaged, the setting
must be additionally secured by tightening
Anl_TC_MS_2112_SPK9.indb 21 Anl_TC_MS_2112_SPK9.indb 21
GB
the knurled screw (10).
•
If different angle settings are required, the
turntable (8) may be secured in position using
only the knurled screw (10).
•
Lightly press the machine head (4) down
while at the same time pulling the retaining
pin (16) out from the motor mounting; this
causes the saw to move down to the lower
working position.
•
Swing up the machine head (4).
•
By loosening the lock screw (12), the machi-
ne head (4) can be angled to the left up to
45°.
•
Check that the voltage marked on the rating
plate is the same as your mains voltage and
connect up the machine.
5.4 Precision adjustment of the stop rail
(Fig. 7/8)
•
Lower the machine head (4) and fasten in
place with the safety pin (16).
•
Fasten the turntable (8) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (5) and the stop rail (7).
•
Slacken the adjustment screws (28), set the
stop rail (7) to 90° in relation to the saw blade
(5) and retighten the adjustment screws (28).
5.5 Precision adjustment of the stop for 90°
cross-cuts (Fig. 8-10)
•
Lower the machine head (4) and fix with the
lock pin (16).
•
Slacken the tightening screw (12).
•
Place the stop angle (a) between the saw bla-
de (5) and the rotary table (8).
•
Slacken the counter nut (29) and adjust the
setting screw (18) until the angle between the
saw blade (5) and the rotary table (8) equals
90°.
•
Re-tighten the counter nut (29) to fix the ma-
chine in this setting.
•
Finally, check the position of the angle indica-
tor (11). If necessary, release the pointer with
a crosstip screwdriver, move to the 0° position
of the angle scale (15) and retighten the hol-
ding screw.
•
No stop angle included.
5.6 Precision adjustment of the stop for 45°
mitre cuts (Fig. 8/12)
•
Lower the machine head (4) and fix with the
lock pin (16).
•
Fix the rotary table (8) in 0° position.
•
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the
- 21 -
19.09.2019 14:23:16 19.09.2019 14:23:16