Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6.5
Arm/disarm an intrusion control panel
(only via IK3 EU)
!
Reader with keypad
- Hold data carrier in the reading range and remove.
- Green LED lights up
- Yellow LED lights up when disarmed and remains dark
when armed.
- Strike the corresponding key (arm or disarm).
- Acknowledgement (according to tables below).
!
Reader without keypad
- Hold data carrier in the reading range and remove.
- Green LED lights up
- Yellow LED lights up when disarmed and remains dark
when armed.
- Hold data carrier again in the reading range after 1 to max 4
seconds.
- Acknowledgement (according to tables below).
Acknowledgement when arming
Fulfilled with
Optical
authorization
and positive drive
Disarmed
Disarmed Armed
(yellow)
Ready
5 sec.
(green)
Alarm
(red)
1 sec.
Acoustical
(signal)
Acknowledgement
System will be armed
Action
Acknowledgement when disarming
Fulfilled with
Optical
authorization
and positive drive
Disarmed
Armed
Disarmed
(yellow)
Ready
5 sec.
(green)
Alarm
Lights up in
(red)
case of alarm
1 sec.
Acoustical
(signal)
Acknowledgement
System will be
Action
disarmed
6.6
AC function after disarming
Depending on the system programming
either
- Disarm first (see 6.5).
- To open the door, hold the IK data carrier
reading range
or
- AC function will automatically be active after disarming.
10
With authorization
No authorization
but no positive drive
5 sec.
5 sec.
Lights up in
case of alarm
1 sec.
1 sec.
Acknowledgement
Acknowledgement
System will
not
System will
be armed
be armed
With authorization
No authorization
but no positive drive
5 sec.
Lights up in
case of alarm
1 sec.
1 sec.
Acknowledgement
Acknowledgement
System will
not
System will
be disarmed
be disarmed
once again
7.
Operating instruction 2
Reader on IK3 EU BUS-2 / DCM from V11.xx
7.1
Operating and indication elements
LED indication
LED yellow
LED green
LED red
Disarming
The state of the indicator is as follows:
7.2
Acoustic acknowledgement
- Buzzer signals:
Reading acknowledgement
after activating every key or data carrier
acknowledgement.
not
Positive acknowledgement
for successfully performed action.
Negative acknowledgement
There is no authorization or the action cannot be
performed.
7.3
Learning mode for data carriers
Learning mode is possible only in the
In learning mode it is simple to authorize new data carriers or delete
existing ones. Newly "learned" data carriers automatically receive
general authorization
(MB256 plus) the PINs / authorizations /time zones must be assigned
afterward via the programming functions.
To start the learning mode, you need a "
carrier set up exclusively for this purpose in the system. However, the
learning key has no authorizations.
As long as learning mode is activated, you can enter or delete as many
data carriers as you want one after another.
not
Visual acknowledgement:
the "Ready" indicator (green LED) serve as a visual acknowledgement
signal in learning mode.
The red LED is lights up in case of alarm
Acoustic acknowledgement:
Positive acknowledgement:
Negative acknowledgement
in the
Meaning:
Disarmed
Ready
Alarm
Numerical keypad
When idle, all indicators remain dark.
When a function is being performed,
the indicator is actuated for approx. 5
seconds according to the function.
For details see following Chapters.
Arming
off
(4x short in 2 sec.)
disarmed state
as of version V9 (MB24/48/100) and version V3
learning key
The "Disarmed" indicator (yellow LED) and
- Learning mode activated
- Data carrier authorized
- Data carrier erased
Invalid action.
An invalid action is given if a programmed
data carrier is to be learned or an
unprogrammed data carrier is to be
erased.
on
flashing
125 ms
2 sec.
2 sec.
.
". This is a data
Werbung
