Herunterladen Inhalt Inhalt Diese Seite drucken

Maintenance - Nice FT210 Anweisungen Und Hinweise Für Den Installateur

Optical device
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 45
5.5) Troubleshooting
Table 6 gives possible indications on how to deal with malfunctions that may be met during installation or due to a fault.
Table 6: Fault diagnostics
Symptoms
The gate cannot be controlled; all the LEDs on the FT210
receiver are off
The gates starts to move but stops after 1 second; LED 2 (yel-
low) is on
The gate stops during the manoeuvre the manoeuvre is inver-
sed; the LED L1 (red) is constantly on.
The gate stops during the movement or the manoeuvre is
inverted; the LED L3 (red) is on and the LED L4 (green) is off
Sometimes the gate stops during the movement or the manoeuvre
is inverted; the LED L1 (red) flashes rapidly when the gate is open.
On activation of the device, the receiver has yellow led L2 lit
and red led L1 flashing. If the infrared beam is interrupted, led
L1 is permanently lit, but no relay activation is heard
Sometimes the gate stops during the movement or the manoeu-
vre is inverted; sometimes everything blocks and cannot be con-
trolled; the LED L2 (red) continues to make 2 short flashes.

6) Maintenance

The FT210 does not require any particular maintenance, however a control should be performed at least once every six months
to check the integrity of FT210 photocell (presence of dampness, rust, etc), cleaning of the external casing and testing as
described in chapter 4 "Testing". The FT210 photocell has been designed to function under normal conditions for at least 10
years, therefore maintenance should be performed more frequently once this period has expired.
7) Disposal
As in installation, also at the end of product lifetime, the disassem-
bly and scrapping operations must be performed by qualified per-
sonnel. This product is made up of different types of material, some
of which can be recycled while others must be disposed of. Seek
information on the recycling and disposal systems envisaged by the
local regulations in your area for this product category.
Caution: some parts of the product may contain pollutant or haz-
ardous substances which, if disposed of into the environment,
may cause serious damage to the environment or physical health.
As indicated by the symbol in figure 31, disposal of this product
in domestic waste is strictly prohibited. Separate the waste into
8) Accessories
The following accessories are available:
• FA1: metal vandal-proof casing, fitted as in figure 32
• FA2: ixing brackets for "MOCF" posts, fitted as in figure 33
32
Downloaded from
www.Manualslib.com
33
manuals search engine
Advisable checks
Check if the receiver is connected to the power supply by
measuring the voltage on the 12/24V terminals.
The outcome of the test at the beginning of the manoeuvre was
negative and there is a possible connection or programming
error or there is a fault in the TX movement sensor of the gate.
Check for possible obstacles or the alignment of the TX and
RX through the entire course of the gate.
The sensitive edge has cut-in. Remove the possible obstacle
and check that the sensitive edge is working correctly.
Check the alignment between the TX and RX throughout the
entire course of the gate.
The receiver is set to Phototest mode (JP1 inserted) but has
still not performed the test at the start of the manoeuvre. If the
central has the Phototest function, leave jumper JP1 of the
receiver inserted, check the connections and perform an
automation manoeuvre. If the control does not have the Pho-
totest function, the jumper JP1 must be inserted incorrectly.
Deactivate the jumper and check that the relays are activated,
interrupting the infrared beam.
The TX battery is flat and communication between the TX and
RX does not occur when conditions are poor. The flashing
LED L (red) indicates that the battery need changing.
categories for disposal, according to the
methods envisaged by current legislation in
your area, or return the product to the retail-
er when purchasing a new version. Local
legislation may envisage serious fines in the
event of abusive disposal of this product.
Warning: the product operates with batteries that could contain
polluting substances and therefore should not be disposed of
along with household waste. After they have been removed from
the product (see paragraph "Battery replacement" in chapter
"FT210B installation instructions and warnings") they should be
disposed of in compliance with the legislations locally in force.
• FTA1: 3.6V battery; 7Ah type C, fitted as in figure 34
• FTA2: 3.6V battery; 2Ah type AA, fitted as in figure 35
34
31
35
13
GB

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis