Before Use - cecotec Mambo 8090 Bedienungsanleitung

ENGLISH

4. BEFORE USE

Note: The product will produce a light smell when it is used for the first time and will disappear
after a few minutes.
This is due to the manufacturing rests and does not affect to its operating.
Take the product out of the box and remove all packaging materials.
Make sure the product is in good conditions. If any sign of visible damage is observed,
contact immediately with our official Technical Support Service.
Place the appliance on a clean, stable and flat surface. Do not place it close to the edge,
inside built-in wardrobes or hanging brackets.
Clean the appliance before using it for the first time.
Connect it to a power supply and press the power switch to turn it on.
The machine will beep and the display will turn on.
5. OPERATION
ON/OFF
Fig. 10.
Use this switch to switch the product on and off.
START/PAUSE
Press the knob on the product's front part to activate the device.
From the main display, select the desired function.
During the setting process, long-press the knob for 2 seconds to reset all settings.
While it is cooking, press the knob to stop it and long-press it for 2 seconds to reset all settings.
After 10 minutes of no operation, the device will enter standby mode.
Once the desired setting or program has been selected, press the knob to activate it and the
device will start operating.
During operation, press the knob to pause the cooking process, the display will show "PAUSE".
You can open the lid, stir or mix food, remove the jar etc. then, place every element back in its
correct position and press the knob again to resume operation. After 10 minutes in "PAUSE", the
device will automatically turn off.
Use the knob to adjust all settings: time, temperature etc. Turn it clockwise to increase the
value and anticlockwise to decrease it.
TIMER
The display shows 88:88:88, as: hour:minutes:seconds.
30
Press the timer button once, the minute digits will flash. Turn the knob left or right to adjust the
desired minutes. Press it again to switch to seconds, the seconds digits will flash. Press it again
to switch to hours. Turn the knob left or right to adjust the desired hours.
During operation, press the timer button and the device will start counting down automatically.
If the timer has not been set, the product will operate with the preset times:
Heating (without blending): max. 12 hours.
Blending (speed 1-4): max 1 hour.
Blending (speed 5-10): max. 5 minutes.
SPEED
Press this button to enter speed-setting mode. The speed icon will flash on the display.
Turn the knob left to decrease speed and right to increase it, from level 1 to 10.
If the selected speed is 5-10, the timer will only be set up to 5 minutes. For the rest of the speed
options, 1 hour.
Warning:
When speed changes from 5 to 6 or when the device starts working, the device could emit
some noise. This is completely normal and does not affect the device's operation.
To crush or chop hard or large quantities of food, select speed 5 at first and then switch it to 10
to ensure perfect performance.
TEMPERATURE
Press this button to enter temperature-setting mode. The temperature icon will flash on the
display.
Turn the knob left to decrease the temperature and right to increase it, from 37 ºC to 120 ºC. The
selected temperature value will blink until the robot reaches the set temperature.
The temperature indicator will turn on red when the jar reaches very high temperatures, as a
warning to avoid burns.
If the temperature icon is red and you want to operate the machine at a high speed, reduce the
food quantity to below 1.5L.
HEATING POWER
Press this button to enter heat-power setting mode. The heat power icon will flash on the
display.
Turn the knob left to decrease heat power and right to increase it, from level 1 to 10.
Low heat power is suggested to cook fatty foods to avoid it from burning and small quantities
of food, as both require precise temperature and control.
High heating power will cook food much faster.
The heat power function will not activate unless the temperature is set too. It is suggested to
use the default setting for each temperature level.
ENGLISH
31