Optional Accessories - Makita DRT50 Betriebsanleitung

Using the tool with the offset base
The offset base is convenient for work in a tight area
such as a corner.
► Fig.59
Using the trimmer base with the
offset base plate and grip
The offset base plate can also be used with a trimmer
base and a grip attachment (optional accessory) for
more stability.
1.
Loosen the screws on the base plate, then remove
the base plate from the offset base.
► Fig.60: 1. Offset base plate 2. Trimmer base plate
2. Attach the offset base plate to the trimmer base by
tightening the screws.
3. Attach the grip attachment and the bar type grip to
the offset base plate by tightening the screws.
► Fig.61: 1. Bar type grip 2. Grip attachment
The knob type grip removed from the plunge base can
be installed on the offset base instead of the bar type
grip.
► Fig.62: 1. Screw 2. Knob type grip
Using the tool with the plunge base
Always hold the grips firmly with both hands during
operation. Operate the tool in the same way as the
trimmer base.
Using the straight guide
Optional accessory
1. Install the straight guide to the guide holder by
tightening the wing nut. Insert the guide holder into the
holes in the plunge base, and then tighten the wing
bolts.
► Fig.63: 1. Wing bolt 2. Guide holder 3. Wing nut
4. Straight guide
2.
Loosen the wing nut on the straight guide and
adjust the distance between the bit and the straight
guide. At the desired distance, tighten the wing nut.
► Fig.64: 1. Wing nut
3. Operate the tool in the same way as the straight
guide for the trimmer base.
► Fig.65
Using the templet guide
Optional accessory
1. Loosen the screws on the base and remove them.
Place the templet guide on the base, and then tighten
the screws.
► Fig.66: 1. Screw 2. Templet guide
2.
Operate the tool in the same way as the templet
guide for the trimmer base.
► Fig.67
Using the parallel ruler
The parallel ruler is effectively used for straight cuts
when chamfering or grooving. Adjust the distance
between the bit and the parallel ruler. At the desired
distance, tighten the wing bolts to secure the parallel
ruler. When cutting, move the tool with the parallel ruler
flush with the side of the workpiece.
► Fig.68
If the distance (A) between the side of the workpiece
and the cutting position is too wide for the parallel ruler,
or if the side of the workpiece is not straight, the parallel
ruler cannot be used.
In this case, firmly clamp a straight board to the work-
piece and use it as a guide against the plunge base.
Feed the tool in the direction of the arrow.
► Fig.69
Changing knob type grip to bar type
grip
To install the bar type grip on the plunge base, loosen
the screw of the knob type grip, then remove the knob
type grip, and then install the bar type grip by tightening
it.
► Fig.70: 1. Knob type grip 2. Screw 3. Bar type grip
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Straight and groove forming bits
• Edge forming bits
• Laminate trimming bits
19 ENGLISH