Specifications; Safety Instructions - Makita HR2020 Betriebsanleitung

ENGLISH
1 Grip base
2 Side grip (auxiliary handle)
3 Teeth
4 Protrusions
5 Loosen
6 Tighten
7 Bit shank
8 Bit grease

SPECIFICATIONS

Model
Capacities
Concrete
Tungsten-carbide tipped bit ....................... 20mm
Core bit ...................................................... 54mm
Diamond core bit (dry type) ....................... 65mm
Wood ........................................................... 32 mm
Steel ............................................................ 13 mm
-1
No load speed (min ) .................................... 0 – 1,050
Blows per minute ............................................ 0 – 4,050
Overall length ................................................. 352 mm
Net weight ...................................................... 2.3 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Intended use
The tool is intended for hammer drilling and drilling in
brick, conorete and stone. It is also suitable for drilling
without impact in wood, metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4
Explanation of general view
9 Bit
10 Chuck cover
11 Depth gauge
12 Switch trigger
13 Lock button
14 Reversing switch lever
15 Action mode changing knob
16 Blow-out bulb
HR2020/HR2020X
4.
5.
6.
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
12. Secure work
17 Dust cup
18 Chuck adapter
19 Keyless drill chuck
20 Sleeve
21 Ring
22 Tighten
23 Loosen
HR2021
20mm
54mm
65mm
32 mm
13 mm
0 – 1,050
0 – 4,050
352 mm
2.3 kg
Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
Don't force tool
It will do the job better and safer at the rate for
which it was intended.
Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommendemd when
working outdoors. Wear protective hair covering
to contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to oper-
ate tool.
HR2022
20mm
54mm
65mm
32 mm
13 mm
1,050
4,050
352 mm
2.3 kg