Personal Safety - Casals CTR305 Bedienungsanleitung

turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired
- Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
- Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained

PERSONAL SAFETY

- Stay alert, watch you are doing and use com-
mon sense when operating a power tool. Do not
use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury
- Use clamps or another practical way to se-
cure and support the workpiece to a stable
platform. Holding the work by your hand or
against the body leaves it unstable and may
lead to loss of control
USE AND CARE
- This machine may only be started and operated
by persons familiar with crosscut saws and
are aware of the dangers associated with the
operation of crosscut saws. Persons under 18
years of age may use this machine only in the
course of their vocationally training, under the
supervision of an instruction.
- These operating instructions are intended
for people with basic technical knowledge
regarding the operation of a machine like this.
Inexperienced persons are strongly advised
to seek competent advice and guidance from
an experienced person before operating this
machine.
- Keep bystanders, particularly children, out of
the danger zone. Do not permit other persons
to touch the machine or power cable while it is
running
- Do not let persons, especially children, not
involved in the work touch the appliance or the
extension cord and keep them away from the
work area.
- When not in use, the appliance should be
stored in a dry locked-up place, put of reach of
children.
- Use the right the appliance. Do not force small
appliances to do the job of a heavy-duty tool.
- Do not use the appliance for purposes not
intended, for example do not use circular saws
to cut tree limbs or logs.
- If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
- Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
- Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control
- Follow instructions for lubricating, chain
tensioning and changing accessories.
Improperly tensioned or lubricated chain may ei-
ther break or increase the chance for kickback.
- Keep handles dry, clean, and free from oil
and grease. Greasy, oily handles are slippery
causing loss of control.
- Disconnect the appliance from the mains when
not in use and before undertaking any cleaning
task.
- Unplug the appliance from the mains before
replacing any accessory.
- Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury
- Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
the power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energizing pow-
er tools that have the switch on invites accidents
- Never use the machine without guard. Keep
guards in place.
- Always keep sufficient distance to the saw
blade. Use suitable feeding aids, if necessary.
Keep sufficient distance to driven components
when operating the machine.
- Wait for the saw blade to come to a complete
stop before removing cutoffs, scrap, etc, from
the work area.
- Do not attempt to stop the saw blade by pushing
the work piece against its side.
- Ensure that when turning ON no tools or loose
parts are left on or in the machine.
- Wear gloves when changing the cutting blade
- Store the saw blade(s) in such manner that
nobody can get hurt.
- Ensure that riving knife is correctly set when