Instructions Of Use; Connection Of A Dust Collector - Casals CTR305 Bedienungsanleitung

INSTRUCTIONS OF USE

- Note: In this section, the essential operating
elements of the machine are introduced.
- The proper use of the saw is detailed in Section
"USE", read this section before using the saw
for first time.
TABLE SAW MODE OPERATION (FIG.2, 5, 6, 12)
- Place the lower blade guard (14) from the left
hand side in front of the kerf plate's rear end
and push towards the rear.
- Ensure the table is fully assembled in the
correct orientation (Fig. 2), ensure that the lock
down pin (22) is positively located and locked to
ensure the secondary switch (Switch B (29)) is
engaged.
- Remove rip fence (4).
- To start and stop the machine, use the ON/OFF
switch (7).
MITRE SAW MODE OPERATION (FIG.6)
- Ensure the rip fence (4) is correctly installed
to cover the saw blade. This activates switch A
(8). Ensure the cover (rip fence) is securely fas-
tened. If not, use rip fence knob (5) to secure.
- Remove the lower blade guard (14).
- To turn the motor on, press on trigger (20) at the
handle.
- To turn the motor off, release the trigger (20).
ROTATING TABLE (FIG.7-9)
- The rotating table (11) turns through 50o to the
left and through 60o to the right and engages in
preset stops at the 0º, 15º, 22.5º, 30º, 45º and
60º position.
- For turning the mitre table, the lock (9) must be
loosened
- CAUTION: In order to prevent the mitre angle
from changing during cutting, the mitre table's
lock knob must be tightened (also when the
table is engaged at the preset stops.)
BEVEL TILT SETTING (FIG.10-11)
- The track arm holder can be tilted from vertical
through 45º to the left.
- For tilting the track arm holder, the bevel locking
lever (16) must be loosened.
- CAUTION: In order to prevent the bevel angle
from changing during cutting, the track arm
holder's lock screw must be tightened (also
when engaged in the preset stops).
RIP FENCE (FIG.12-13)
- The rip fence (4) is mounted on the upper saw
table (1).
- The rip fence lock knob (5) must point towards
the front of the machine.
- After loosening the lock knob, the rip fence (4)
can be removed and repositioned in crosscut
saw mode(Fig.13) the rip fence is positioned
over the blade guard (3). When repositioning
the rip fence, always ensure you secure the
fence using the rip fence lock knob (5).

CONNECTION OF A DUST COLLECTOR

- DANGER: Some types of wood dusts (e.g.
beech, oak, ash) may harmful to health when
inhaled. Use a dust collector:
- When using the saw in enclosed spaces;
- When using the saw over extended periods
(more than ˝ hour per day);
- When cutting oak, beech or ash.
- The dust collector must comply with the follow-
ing requirements:
- Fitting the dust extraction port diameter (43mm);
- Air flow volume ≥ 550m3/h;
- Vacuum at the dust extraction port of the saw ≥
740 Pa;
- Air speed at the dust extraction port of the saw
≥ 20m/s.
- Observe and follow the dust collector's operat-
ing instructions as well.
ADJUSTING THE RIVING KNIFE (FIG.15)
- DANGER: Unplug before adjustment
- NOTE: The riving knife is factory-set to the
position. An alignment before initial operation is
only necessary if the riving knife's position has
changed during transport.
- Checking the riving knife:
- Distance between the saw blade's outer edge
and the riving knife must be 3-8mm.
- The riving knife must be in alignment with the
saw blade
- DANGER: The riving knife is one of the safety
devices and must be correctly installed for a
safe operation.
- Only if realignment of the riving knife is neces-
sary:
- Loosen hexagon socket screws (B1). Adjust
riving knife (2) to desired position. Distance be-
tween the saw blade's outer edge and the riving
knife must be 3-8mm.
- Tighten hexagon socket screws (B1).