Bosch GTM 12 JL Professional Originalbetriebsanleitung Seite 40

40 | English
Technical Data
Combination Saw
Article number
3 601 M15 ...
Rated power input
No-load speed
Laser type
Laser class
Weight according to
EPTA-Procedure 01:2014
Protection class
Permissible workpiece dimensions (maximal/minimal):
Chop/mitre saw, see page 44
Table saw, see page 47
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 61029-1, EN 61029-2-11,
EN 60825-1.
EC Type Examination No. 4811001.12001 by notified test-
ing agency No. 2140.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 17.06.2015
Assembly and Transport
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
1 609 92A 1T0 | (28.10.15)
GTM 12 JL
... 0.. ... 061
W 1800
-1
min 3800
nm 650
mW < 1
2
kg 23
/II
mm 300–305
mm 1.5–2.0
mm
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Delivery Scope
Carefully remove all parts provided from their packaging.
Remove all packing material from the power tool and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
1650
check if all parts listed below have been supplied:
3700
– Combination saw with pre-mounted saw blade
– Allen key/slotted screwdriver 5
650
– Dust bag 8
< 1
Additionally for table saw:
2
– Parallel guide 61
– Push stick 62
23
– Lower saw blade cover 66
/II
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Stationary or Flexible Mounting
 To ensure safe handling, the machine must be mounted
30
on a level and stable surface (e. g., workbench) prior to
using.
Mounting to a Working Surface (see figures a–b)
– Fasten the power tool with suitable screw fasteners to the
working surface. The mounting holes 3 serve for this pur-
pose.
or
– Clamp the power tool with commercially available screw
clamps by the feet to the working surface.
Mounting to a Bosch Saw Stand
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long
workpieces.
 Read all safety warnings and instructions included with
the worktable. Failure to observe safety warnings and in-
structions can lead to electrical shock, fire and/or cause
serious injuries.
 Assemble the worktable properly before mounting the
power tool. Perfect assembly is important in order to pre-
vent the risk of collapsing.
– Mount the power tool in transport position on the saw
stand.
Flexible Mounting (not recommended!)
In exceptional cases, when it is not possible to mount the ma-
chine onto a level and stable work surface, it can be set up us-
ing the tilt protector.
The tilt-protector bar 6 is used for this purpose.
 Never remove the tilt-protector bar. Without the use of
the tilt-protector bar, the machine does not stand safely
and can tip over, especially when sawing at maximum mi-
tre/bevel angles.
Bosch Power Tools