Whirlpool WBC 3546 A+NFCX Produktangaben Seite 4

DEFROSTING THE REFRIGERATOR COMPARTMENT
Refrigerator compartment defrosting is completely automatic.
Droplets of water on the rear wall inside the refrigerator compartment
indicate that the automatic defrost phase is in progress. The defrost
water is automatically run into a drain hole and collected in a container,
where it evaporates.
DEFROSTING THE FREEZER COMPARTMENT
No Frost freezers provide chilled air circulation around the storage
areas and prevent the formation of ice, thereby completely eliminating
the need for defrosting. Frozen items don't stick to the walls, labeling
stays legible and storage space remains neat and clear.
REPLACING THE LIGHT BULB
Always disconnect the refrigerator from
the power supply before replacing any
light bulb.
If the inside light is not working, it is
necessary to:
1. Remove the light cover: put the fingers into the side ventilation holes
(1), stretch the cover gently and move it upwards.
2. Check the bulb. If necessary unscrew the broken bulb and replace it
with the new one (use maximum 15W bulb).
3. Put on the light cover.
Do not leave the bulb uncovered.
GUIDE TO SELECTING FUNCTIONS
Functions and settings
Fast Freezing: For more efficient freezing activate this function 48
hours before freezing fresh products.
- Select Freezer compartment by using button (1), LED (2) shall turn
ON.
- Press and hold the temperature setting button Temp.°C until 3 green
LEDs light up simultaneously (4) (5) (6).
After 24 hours place the food to be frozen in the upper basket of the
freezer compartment.
This function is automatically disabled after 48 hours. To
deactivate it earlier follow the procedure:
- Press and hold by 3 sec. the temperature setting button Temp.°C
again while the LED (2) remains ON - the temperature selection
lights will return to previous displayed temperature setpoint.
Reset alarm
If any alarm appears, the user could reset the acoustical sound by
pressing once Reset alarm pushbutton.
"Black-out alarm" (power supply failure) - in case of power failure,
the appliance automatically monitors the temperature changes in the
freezer compartment after the power supply returns. The "Black-out
alarm" will activate, if the temperature has risen above the admissible
level. This is indicated by:
OTHER ABNORMAL APPLIANCE OPERATIONS DISPLAYED BY LEDs
In case of abnormal appliance operation, all the temperature selection LEDs will flash and one beep will sound. To check the code
alarm user have to press and hold the temperature setting Temp.°C & Reset alarm pushbuttons and alarm code will be showing on
the temperature LEDs (possible alarm codes are explained in the table below).
When this operation is released, the LEDs will flash until the fault is eliminated. If any alarm shown in the table occurs, the
fridge/freezer functions such as temperature adjustment, super freezing are not available until the fault is eliminated.
When several alarms occur simultaneously, the alarm with the highest priority is displayed (Number 1 being the highest priority).
Alarm
Evaporator Temperature Sensor Alarm - Freezer compartment
Evaporator Temperature Sensor Alarm - Fridge compartment
Ambient Temperature Sensor Alarm - Freezer compartment
Description LED OFF
D GB F
PRODUCT SHEET
Codification to be displayed by
Priority
LED 4
1
2
3
NL E P I GR
- Flashing of the green LED (2)
- Activation of a beep.
When the "Black-out alarm" is actived, it is recommended to proceed
as follows:
- If the food in the freezer is not frozen but is still cold, transfer it
promptly to the refrigerator compartment and consume within 24
hours.
- If the food in the freezer is frozen, it has re-frozen after thawing
caused by the power failure. The consumption of re-frozen food is
not recommended because it has lost its nutritive value and may be
hazardous to your health.
Note
The "Black-out alarm" does not guarantee the food quality and its
safety in case of consumption. It only indicates the necessity to assess
the quality of food in the freezer and refrigerator compartments.
To deactivate the alarm, press once Reset alarm pushbutton, the
flashing of the green LED (2) go off.
- The temperature will return to the normal operating cycle level and
the beep will stop.
Door open alarm
When the refrigerator compartment door remains open for more than 2
minutes, the beep is activated.
When the door is closed the product returns to normal operation, the
beep will stop.
"6th Sense" function
The "6th Sense" function helps to maintain optimal conditions to
storage of food and is automatically activated when:
• a large amount of food is loaded into the freezer;
• the freezer door is left open for a long time;
• a prolonged power failure takes place, causing the internal
temperature of the appliance to increase to values that cannot
guarantee safe storage of food.
Fresh Control
The Fresh Control is activated by default and is working only with Fan
on. To disactivate the Fresh Control function press for at least 3 sec.
both buttons Cavity selection "Fridge / Freezer" and "Temp.°C". A
long sound signal will be provided for the deactivation of the Fresh
Control.
In order to activate this function follow the same procedure (keeping
pressed the 2 buttons for 3 sec.). A short sound signal will be provided
for the activation of the Fresh Control.
This function controls the fridge fan in order to optimize food
preservation in any ambient temperature conditions.
To minimize the Energy consumption is suggested to disable the Fresh
Control function and fan.
temperature LEDs
LED 5 LED 6
Contact the After-Sales Service and provide the alarm code.
Contact the After-Sales Service and provide the alarm code.
Contact the After-Sales Service and provide the alarm code.
LED ON
S N DK FIN PL
Action
CZ SK H RUS BG
GB
RO