Warning - Cino CN-KA Handbuch

2. Return to Factory Setting
KA: Press large cup volume button and power button together for 3s in the standby mode,
then you will hear a "beep". The machine will be restored to factory setting and return
back into standby mode.(volume button indicators blink 3 times at 1 time/s together)
KB: Turn off and on the power, the machine returns to factory setting.
3. Power save mode
KA: a. If machine hasn't been operated for 10 minutes in the sandby mode the machine
will go to power saving mode automatically.
b. Press power button in any mode, after you hear a beep", the machine will go to
power saving mode.
c. In order to use the machine in power saving mode, you need to press the power
button again. Then the machine goes back to standby mode.
KB: If machine hasn't been operated for 10 minutes in the standby mode the machine
will go to power saving mode automatically. Now brewing indicators will always be
on, volume indicators will light 1s and pause 2s alternatively.
4. Temperature selection
KB: Switch the temperature knob clockwise to increase the temperature.
Switch the temperature knob anticlockwise to decrease the temperature.
5.Clear the System
KA: Press big cup button and small cup button together for 3s in the standby mode, then you will
hear a beep, both big and small volume buttons blink at 2 times/s together, the machine goes
to "Clear the System" mode. After emptying the machine both the boiler and the pump stop
working (after you hear a "beep", both the big and small volume buttons blink at 2 times/s
alternatively, now Clear the System is completed).Then press power button or plug out the
power cable to exit Clear the System mode.
6.Descaling
KA: Press and hold both the medium and small cup buttons for 3 seconds in the standby mode,
when after a "beep", the machine goes to Descaling, both the boiler and pump work at the
same time until the water in the water tank is pumped dry. ( After a long "beep", both the
medium and small cup button blink 2 time/s together, Descaling is finished ). Nowpress
power button or plug out the power line to exit Descaling.

Warning

Handle not closed
KA: When the handle isn't closed in the right position, the machine signals a warning: the small cup
indicator blinks at 2 times/s continuously. Closing the handle can disengage the warning.
KB: If Handle isn't closed in the right position, the machine will send out a warning: all volume
indicators blink at 4Hz.
8
Water shortage
KA: When there is a water shortage, the machine will signal a warning: the medium cup indicator
blinks at 2 times/s continuously and the machine beeps continuously at 2 times/s.
Now refill the water tank and press any volume key to disengage the warning.
KB: When there is a water shortage, the machine will send out a warning: all indicators blink at 3Hz.
Capsule blocked
KA: If the capsule gets stuck/blocked in the chamber because it is outdated or damaged, the
machine will send out the warning with the medium cup indicator blinking at 2 times/s
accompanied with a synchronized "beep". Now you need to open the handle, change the
capsule and press any volume button to disengage the warning.
KB: If there is something wrong with the capsule, coffee can not be brewed and the machine
will send out a warning: big cup indicator blinks at 2Hz.
NTC warning
KA: When there is an NTC error, the machine can't work and it will shut down both boiler and
pump. All the three volume buttons blink together at 2 times/s synchronized with "beep".
Now you need to call for Service.
KB: When there is an NTC error, the machine will shut down and send out a warning: volume
indicators blink at 1Hz.
Excessive pump work
KA: If the pump works over 2 minutes continuously, there will be a warning:The big volume
button blinks at 3 times, pausing 3 seconds synchronized with "beep". To disengage the
warning, simply stop the machine and rest it for 1 minutes before reuse.
9