Accessories; Protecting The Environment - Black+Decker BDCJS12 Originalanweisung

@
Warning! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C.
Recommended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell temperature
warms up or cools down.
● To charge the battery (8) (Not supplied), insert the USB
charger (9) Not Supplied.
● Connect the USB charger to a power source.
The charging indicator will blink. The charge is complete
when the charging indicator switches to continuously on.
● The charger and the battery can be left
connected indefinitely.
● Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Fitting and removing the battery (fig. B)
● To fit the battery (8) (Not supplied), line it up with the
receptacle on the tool. Slide the battery into the receptacle
and push up until the battery snaps into place.
● To remove the battery, push the release button (10) while
at the same time pulling the battery out of the receptacle.
Fitting and removing the saw blade (fig. C)
● Hold the saw blade (7) with the teeth facing forward.
● Lift the saw blade locking lever (3) upwards.
● Insert the shank of the blade fully into the blade clamp (4)
as far as it will go.
● Release the lever.
● To remove the saw blade (7), lift the saw blade locking
lever (3) upwards and pull the blade out.
Switching on and off (fig. D)
● To switch on, slide the lock off switch (2) to the left then
pull and hold the variable on/offtrigger switch (1).
@
● To switch off, release the trigger switch (1).
Warning! Do not switch the tool on or off while
@
under load.
Warning! Always slide the lock off switch (2) to the
right, the locked position when the tool is not in use.
Storage of spare blades (fig. E)
● Spare blades (7) can be stored in the recess (12) on the
main body of the tool.
Sawing
● Always hold the tool with both hands.
● Let the blade run freely for a few seconds before starting
the cut.
● Apply only a gentle pressure to the tool while performing
the cut.
● If possible, work with the shoe plate (6) pressed against
the workpiece. This will improve tool control and reduce
tool vibration, as well as prevent the blade from
being damaged.
(original instructions)
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
● Use a fine-tooth saw blade.
● Saw from the back surface of the workpiece.
● To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
● Use a saw blade suitable for sawing metal. Use a
finetooth saw blade for ferrous metals and a coarser saw
blade for non-ferrous metals.
● When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
● Spread a film of oil along the intended line of cut.

Accessories

The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
This tool is suitable both for U-shank and T-shank saw blades
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
English
7