Residual Risks - Black+Decker BDCJS12 Originalanweisung

English
(original instructions)
Safety of others
● This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
● Children should be supervised to ensure that they do not
play with the appliance.

Residual Risks

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
● Injuries caused by touching any rotating/moving parts.
● Injuries caused when changing any parts, blades
or accessories.
● Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
● Impairment of hearing.
● Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
@
preliminary assessment of exposure.
Warning! The vibration emission value during actual
use of the power tool can differ from the declared
value depending on the ways in which the tool is
used. The vibration level may increase above the
level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following symbols are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
6
Additional safety instructions for batteries
and chargers
Batteries
● Never attempt to open for any reason.
● Do not expose the battery to water.
● Do not store in locations where the temperature may
exceed 40 °C.
● Charge only at ambient temperatures between 10 °C and
40 °C.
● Charge only using the charger provided with the tool.
● When disposing of batteries, follow the instructions given
p
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
Chargers
● Use your charger only to charge the battery in the tool
with which it was supplied. Other batteries could burst,
causing personal injury and damage.
● Never attempt to charge non-rechargeable batteries.
● Have defective cords replaced immediately.
● Do not expose the charger to water.
● Do not open the charger.
$
● Do not probe the charger.
The charger is intended for indoor use only.
#
Electrical safety
This charger is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
● If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed trigger switch
2. Lock-off button
3. Saw blade locking lever
4. Blade clamp
5. Blade support roller
6. Shoe plate
7. Saw blade
8. Battery (Not Supplied)
@
Assembly
Warning! Before assembly, remove the battery
from the tool and make sure that the saw blade has
stopped. Used saw blades may be hot.
Charging the battery (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.