Redmond SkyKettle RK-M173S-E Gebrauchsanleitung Seite 9

2. Unwind the power cord to the desired length. Put the excessive part into the
compartment located on the base bottom. If necessary use the extender of a
suitable power (no less than 2.5 kW).
3. Remove the kettle from the base. Press the release button onto the handle.
4. Pour water into the kettle, water level should be between the MIN and MAX points
on the scale. If water level is higher than MAX point, the boiling water may be
splashed. In case of water undersupply the appliance may be switched off in advance.
ATTENTION! The unit is meant only for water heating and boiling.
5. Firmly close the kettle lid and fix it to the base. The unit will work only if it is
fixed correctly.
6. Plug in the kettle. One short audible signal will be heard (if audible signals
are enabled), all the indicators on the panel and display and illumination will
be lit for 1 second. Then the appliance will switch to the standby mode. In the
standby mode the display is not illuminated, the current temperature value of
water in the kettle is displayed at the bottom of the display.
To enable/disable audible signals
1. To disable audible signals in the standby mode press "–" button and, holding
it, press . S indicator will appear on the top of the display, OFF indicator — at
the bottom of the display. The setting will be automatically saved in 5 seconds,
the appliance will switch to standby mode.
2. To enable audible signals in the standby mode press "–" button, and, holding it,
press . S indicator will appear on the top of the display, an audible signal will
be heard, On indicator will appear at the bottom of the display. The appliance
will save the settings and automatically switch to standby mode in 5 seconds.
In the description of the operation process of the appliance it is implied that audi-
ble signals are enabled.
The Ready for Sky technology
The Ready for Sky technology enables to use the software app of the same name to
control the appliance remotely from a smartphone or tablet.
1. Download the software from the App Store or Google Play (depending on your
operating system) onto your smartphone or tablet.
For the minimum supported OS version, see the company's official website www.
redmond.company or the application description at the App Store and Google Play.
2. Open the Ready for Sky app, create an account and follow the prompts that
appear on the screen.
3. Switch the kettle to the standby mode. Press and hold down "+" button
before synchronization starts. An audible signal will be heard. During syn-
chronization and indicators will be alternately lit up on the top of
the display. Then the appliance will switch to the standby mode after the
connection is complete.
If within 10 seconds the connection won't be made, the appliance will switch to the
standby mode.
4. To disable remote control feature press and hold down "–" button in the
standby mode until an audible signal is heard.
To provide stable connection the mobile device should be located within no more
than 15 metres from the appliance.
Appliance control via the wireless network. Instruction on the R4S Gateway application
installation is available through the link: www.readyforsky.com/r4sgateway
Boiling water
1. Press . Water heating process will start. 100°С indicator will be lit on the
top of display. The current temperature value of water in the kettle is displayed
at the bottom of the display.
2. After water comes to a boil an audible signal will be heard, 100°С indicator
will go out and the appliance will switch to the standby mode.
3. To interrupt the water heating process repress
from the base.
Heating water without boiling
This is the recommended mode for bottled artisan or filtered water. Water which has
not been boiled retains its natural properties, which is particularly important when
brewing premium teas. You may adjust the water heating temperature between 40°С
and 90°С in 5°С interval.
1. Press . The button indicator will start blinking. The heating process will
start, heating temperature value will appear on the top of the display (default
temperature is 80°С).
2. Use "+" and "–" buttons to adjust the desired heating temperature value. The
temperature value indicator will start flashing. The appliance will save settings
in a few seconds; the temperature value will be lit up solid.
3. After the desired temperature is reached an audible signal will be heard and
appliance will switch to the heating mode. The temperature value indicator
and button indicator will be lit up solid in this mode.
GBR
SkyKettle RK-M173S-E
FRA
DEU
NLD
ITA
ESP
PRT
DNK
NOR
SWE
FIN
LTU
LVA
EST
ROU
HUN
button or remove the kettle
BGR
HRV
SVK
CZE
POL
RUS
GRE
TUR
UKR
KAZ
9