Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Maschinenelemente
1
Schlüssel sw 4
2
Schraube
3
Grifflasche
4
Handgriff
5
Aufnahme für Schutzhaube
6
Schlüssel sw 17
7
Spindel
8
Schlüssel sw 5
9
Schutzhaube
Griffseite wechseln: Links oder rechts
• Mit Schlüssel 1 Verschraubung 2 der Grifflasche 3 lösen bzw. sicher
spannen.
Schutzhaube
Für die unter 11, 12 abgebildeten und in den technischen Daten spezifi-
zierten Schleifscheiben muss die Schutzhaube 9 unbedingt montiert, d.h.
verwendet werden.
• Schutzhaube 9 über die Aufnahme 5 stülpen.
• Schutzhaube in die richtigen Position drehen
(zwischen Schleifscheibe und bedienender Person ) .
Read the enclosed safety instructions, appendix 30003471!
1. Rotostar: Technical data
2. Flexible shaft
3. Start-up procedures
3.1 Set the operating speed
3.2 Connect the flexible shaft
3.3 Connect the SAK safety clutch
3.4 Connect toolholders
3.5 Start-up with SAK
4. Accessories: FH10, WI10, BSG10, FSM
1. Rotostar
see Fig. A
Machine elements
A1 On/Off switch
A3 Speed indicator
A2 Retention pin
A4 Speeds
Technical data
Universal, single-phase AC motor
Power input:
Power output:
Insulation protection class
Voltage (see spare parts list)
Soft start for smooth starting
Cut-out carbon brushes
Weight without shaft:
No load speeds
Sound pressure level EN 60745
Sound power level
K =
Flexible shaft connection
For flexible shaft types:
(see catalogue)
Vibration values ISO/DIS 8662-4
Toolholder type: Test plate:
FH10
ø 80 x 10
WI10
ø 50 x 6
BSG 10
ø100 x 25
FSM 1:1
ø180 x 6
K =
4
10 Spannflansch
11 Schruppscheibe
12 Trennscheibe
13 Spannmutter
14 Schlüssel zu Spannmutter
15 Spannmutter
16 Elastischer Schleifteller
17 Fiberscheibe
18 Direkt aufschraubbare Werk-
zeuge
GB
A5 Excenter
A6 Motor shaft
1,700
W
1,250
W
II
Various
At 230 V
only
2
10
kg
12,000
RPM
6,000
RPM
3,000
RPM
89
dB(A)
102
dB(A)
3
dB(A)
DIN 10
=
M10
see A6
NA 12 DIN 10/G28
see B2 B8
NA 10 DIN 10/G28
Measured value: Excenter stage:
< 2,5 m/s
2
12,000 RPM
< 2,5 m/s
2
12,000 RPM
< 2,5 m/s
2
6,000 RPM
< 2,5 m/s
2
6,000 RPM
1,5 m/s
2
• Mit Schlüssel 8 Schutzhaube 9 sichern.
Verwendbare Werkzeuge
11, 12 Faserstoffarmierte Schrupp und Trennscheiben, Lamellen-Fächer-
Schleifscheiben, Diamanttrennscheiben
16 Elastischer Schleifteller mit Fiberscheibe 17 und Spannmutter 15, oder
mit Klettenverschluss-Schleifblättern
18 Direkt aufschraubbare Werkzeuge
Werkzeuge wechseln
• Spindel 7 mit Schlüssel 6 festhalten.
• Spannmutter 13 (15) mit Schlüssel 14 lösen oder spannen.
Weiteres Zubehör
ist mit den dazugehörigen Bestellnummern in den SUHNER-Katalogen
aufgeführt.
Änderungen vorbehalten.
Warning: The specified vibration value was measured with a
standardised test method and may differ from the actual operat-
ing value. The specified value can be used for product compari-
sons or for an introductory assessment of work breaks.
Maintenance
• Store machine in a dry, clean place.
• Cooling air ports must be kept free of obstructions.
• Unplug before performing any maintenance work.
• The gear grease must be renewed after every second carbon-
brush change. Your SUHNER Service Centre can perform this
work quickly and efficiently.
• Check connecting cables regularly. Damaged cables must be
replaced under all circumstances.
• Any replacement needed for the connecting line must be
installed by the manufacturer or its agent if safety risks are to be
eliminated.
• Repairs may only be performed by a qualified electrician Acci-
dents could otherwise occur for the operator.
• Complaints can only be accepted if the machine is returned
unopened.
2. Flexible shaft
See Fig. B
Machine elements:
B1 M10 threaded coupling
B2 DIN 10 casing coupler
B3 Spring-loaded pin
Type: NA10 DIN 10/G28, permissible operating speed 15'000 RPM
Type: NA12 DIN 10/G28, permissible operating speed 12'000 RPM
Maintenance
• Store flexible shaft in a dry, clean place.
• If used daily: Re-grease once monthly. Remove core B5 from
casing B4. Remove shaft grease. Lightly apply SUHNER shaft
grease to core B5. Order No. for 1 kg can: 904 832.
• New shafts or newly greased shafts require running-in.
• Clean casing coupler B2 B8 before use. Worn casing couplers
lead to increased vibration and noise. The casing B4 must then
be replaced (see spare parts list).
3.
Set the operating speed
1
• Only change speed when machine is switched off. A1 Wait until
gears are completely motionless. Unplug power supply.
B4 Casing
B5 Core
B6 Driving pin
B7 Spring-loaded pin
B8 G28 casing coupler
(Excenter switch) see Fig. A
Werbung
