Vitek VT-4207 R Betriebsanweisung Seite 4

ENGLISH
• This unit is not intended for usage by children or
disabled persons unless they are given all the nec-
essary and understandable instructions by a person
who is responsible for their safety on safety mea-
sures and information about danger that can be
caused by improper usage of the unit.
• Children and disabled people can use the unit under
supervision only.
• Do not use the unit outdoors.
• Never pull the power cord, when disconnecting the
unit from the mains, take the plug and remove it
carefully from the socket.
• Never use the unit if the power cord or the power
plug is damaged, the unit works improperly or af-
ter it was dropped. Do not try to repair the unit by
yourself. Contact an authorized service center for
all repair issues.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE ONLY
uSiNG oF tHe cookiNG BoWl (3)
• Use the multicooker and its removable bowl (3) for
the intended purposes only. Do not use the cook-
ing bowl (3) with other heating units or cooking
surfaces.
• Do not replace the bowl (3) with any other container.
• Always make sure that the heating element (13)
surface and the bottom of the bowl (3) are clean
and dry.
• Do not use the bowl (3) for mixing products. Never
chop the products in the bowl (3) to avoid damage
of non-stick coating.
• Never leave or keep any foreign objects in the bowl
(3).
• Stir the products in the bowl (3) only with the spat-
ula (17). You can also use wooden, plastic or silicon
accessories.
• Do not use metal objects that can scratch the non-
stick coating of the bowl (3).
• Do not tap on the inner surface of the bowl (3).
• After cooking dishes with spices and seasonings
wash the bowl (3) immediately (see chapter "Clean-
ing and care»).
• To avoid damage of the non-stick coating do not put
the bowl (3) into cold water right after cooking; let it
cool down preliminary.
• The bowl (3) is not intended for washing in the dish-
washing machine.
Before the first use
1. Unpack the unit, remove any stickers and package
materials that can prevent unit operation.
2. Place the unit on a flat, dry, heat-resistant surface
away from water, moisture and open flame. Distance
to the nearest surfaces should be at least 30-40 cm.
Attention! Do not place the unit near bath tubs,
kitchen sinks or other containers filled with water.
Note: After unit transportation or storage at low tem-
perature it is necessary to keep it for at least two hours
at room temperature before switching on.
3. Open the multicooker lid (6) by pressing the but-
ton (2).
4. Remove the protection screen (5) by pressing the
clamps (4).
5. Press the steam valve (11) from the inner side of the
lid and take it out, then dissemble it by turning its
lower part to the position
6. Wash all the removable parts (steam valve (11) parts,
protection screen (5), bowl (3), steam cooking bas-
ket(19), soup ladle (15), spatula (17) and measuring
cup (16)) with a soft sponge with some neutral de-
tergent, then rinse and dry.
7. Wipe the unit body with a damp cloth. Let the unit
dry.
8. Combine the valve parts by matching ledges on the
lower part with grooves on the upper one and turn
the lower part clockwise till locking (position
9. Install protection screen (5) and the steam valve (11)
back to its place.
using of the multicooker
1. Put the necessary products into the bowl.
Note: Make sure that the products and liquids level
doesn't exceed the maximal mark and is not lower than
the minimal level. The maximal mark for porridges (ex-
cept rice) is 3 l, maximal mark for other products and
liquids - "CUP».
2. Place the bowl (3) in the process chamber. Make
sure that the bowl (3) is placed evenly and is in se-
cure contact with heating element (13) surface.
Note:
Do not use the bowl (3) for washing cereals and
chopping products, this can damage the non-stick
coating.
Wipe the outer surface and the bottom of the bowl (3)
dry before use. Make sure that there are no foreign
objects, dirt and moisture in the process chamber and
on the bottom of the bowl.
In the middle of the heating element (13) there is a tem-
perature sensor (14). Make sure that the movement of
the sensor (14) is not limited.
3. If you steam products, insert the basket (19) with
products and pour water in the bowl (3) so that
boiling water doesn't reach the bottom of the bas-
ket (19).
4. Close the lid (6) until click.
5. Insert the power cord into the connector (8), insert
the power plug (18) into the socket.
6. To choose an automatic cooking program, press the
"MENU" button (26) repeatedly till indicator of the
corresponding program appears on the display. In-
dicator will light up on the display.
7. Cooking time in different programs is set by default,
but it can vary within the set range. To change cook-
ing time press the "TIME» button (22), then set the
time with the "HOURS» (20) and "MINUTES» (21)
buttons (see Table 1).
8. Press the "START» button (25) to start cooking.
4
.
).