Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
3G SIGNAL STRENGTH
To check the 3G signal strength it is necessary to:
Enter the User Menu (User Code + (*)).
1.
(
)/(
)
2.
With
select
PHONE 04
▲
▼
3.
With
(
)/(
)
select
SEG. 3G FIELD
▲
▼
show the signal strength detected as shown in the following
key:
= no signal
----
=
low signal
#---
= medium signal
##--
= good signal
###-
= very good signal
####
4.
Press (#)to return to the previous menus.
PHONE
System clock
If the control unit is connected to a network and the NTP service is
used, this menu is not displayed.
To change the system date and time, it is necessary to:
Enter the User Menu (User Code + (*)).
1.
2.
With
(
)/(
)
select
CLOCK 08
▲
▼
(
)/(
)
3.
With
select
HH:MM DD/MM/YY
▲
▼
(
)/(
)
4.
With
scroll between the various date and hour fields and
▲
▼
(+)/(‒)
with
change their values.
5.
At the end of the change press (#). A message will ask you to
confirm the change by pressing
saving with (#).
CLOCK
HH:MM DD/MM/YY
Inputs
ENTRANCES TEST
The entrances menu allows you to check the status of the entrances.
Enter the User Menu (User Code + (*)).
1.
2.
With
(
)/(
)
select
INPUTS 09
▲
▼
3.
With
(
)/(
)
select
INPUTS TEST.
▲
▼
4.
To select/deselect the areas to be tested press the buttons from
(1)
(9)
or (0)+
(0)...(6)
to
and press (*).
and press (*). The display will
04
3G SIGNAL
SIGNAL. 3G FIELD
[0..4] ----
and press (*).
and press (*).
(*)
otherwise to exit without
08
HH:MM DD/MM/YY
YEAR:
XX
HH:MM DD/MM/YY
SECONDS:
XX
and press (*).
10
to 16).
(for those from
5.
Once the entrance configuration to be tested has been se-
(*)
lected, press
to start the test. If there are no open entran-
ces,
will be displayed, otherwise the list of open
CLOSED ENTRANCES
ones will scroll.
INPUTS
ENTRANCES TEST
ENTRANCES TEMP. EXCLUSION
It allows the temporary exclusion of the entrances belonging to the
keypad and to the code.
1.
Enter the User Menu (User Code + (*)).
(
)/(
)
2.
With
select
INPUTS 09
▲
▼
(
)/(
)
3.
With
select
TEMP. EXCLUSION. ENTRANCES
▲
▼
4.
Press the button
(*)
to Exclude / Activate the single input.
INPUTS
EXCLUSION
INPUTS TEMP.
Outputs
The alarm system can allow the management of outputs (commands)
for the purpose of implementing simple operators.
There are two types of outputs:
•
Stable: means an output which, if activated in ON mode,
returns to the OFF status only if commanded by the User or
after a specific event programmed by the Installer.
•
Impulsive: means an output that if activated in ON returns
to the OFF status after a well-defined time set by the In-
staller.
The Installer is responsible to instruct the User in using the
controllable outputs.
In the outputs menu there are two menus:
when exiting the menu they return to the previous status.
OUTPUTS TEST
when exiting the menu, the outputs remain in the se-
CHECK OUTPUTS
lected state.
1.
To command the output it is necessary to press
is impulsive it will be deactivated automatically,
used if it is necessary to forcibly restore it).
To end press (#).
2.
OUTPUTS
OUTPUT
-OFF-
9
ENTRANCES TEST
###
CLOSED INPUTS
# = ESC
and press (*).
.
9
INPUT 1
*=EXCLUDE #=EXIT
INPUT 10
*=EXCLUDE #=EXIT
(*)
(if the output
(*)
it will only be
09
XXX
*=ON
#=ESC
Werbung
Kapitel
Inhaltsverzeichnis
