Werbung
¥
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance. Do not use a
mechanical device or any artificial means to
speed up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it
may get damaged.
Installation
¥
During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
Figure.
Attention: keep ventilation openings clear of
obstruction.
¥
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly
available from the manufacturer or its service
agent.
¥
There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
¥
Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
CONTENTS
Warnings
Operation
Control panel
Cleaning the interior
Starting up
Warning light
Electronic thermometer
Appliance interior
Refrigerator compartment
Drink dispenser
Superchill compartment
Freezer compartment
Useful hints for freezing
Storing frozen foods
Thawing food
Ice cube maker
Maintenance
Cleaning the inside
Defrosting
Periods of no operation
52
¥
If the appliance has been transported horizontally,
it is possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to flow
back in the compressor.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol
are recicable.
51
Replacing the bulbs
Troubleshooting
53
Technical information
53
53
Installation
53
Location
53
Electrical connection
53
54
Positioning
55
55
Height adjustment
56
Fitting the side panels
56
Building the appliance in
57
Fitting the plinth
57
57
57
58
58
58
59
INSTRUCTIONS POUR LÕENCASTREMENT
RŽglage en hauteur
La hauteur de lÕappareil peut •tre rŽglŽe de 820 mm
ˆ 870 mm, afin de consentir lÕalignement avec les
autres meubles de cuisine.
RŽgler la hauteur des roues postŽrieures et des
pieds, avant de mettre lÕappareil entre les autres
meubles.
A lÕorigine, les roues sont rŽglŽes pour une hauteur
de 820 mm. Pour aligner lÕappareil sur 870 mm, il
faut le- soulever au moyen des quatre pieds, en se
servant de la clŽ prŽvue ˆ cet effet, puis enlever les
roues et les remettre dans la position la plus basse.
Montage des panneaux latŽraux
¥
Fixer les Žquerres sur les panneaux, dans la
position indiquŽe sur le schŽma.
La cote 132 est prŽvue pour un socle de 100 mm
de hauteur, ˆ placer sous le panneau. Si le socle
a une autre taille, il faut faire augmenter ou
diminuer la cote 132 en fonction de ses
dimensions.
59
60
60
61
61
61
¥
Monter les panneaux sur lÕappareil.
62
¥
Fixer les Žquerres postŽrieures, en tenant
compte de lÕŽpaisseur des panneaux (900 mm de
62
largeur max. pour le meuble).
62
¥
Fixer les panneaux ˆ lÕavant.
63
Si on utilise des panneaux de moins de 20 mm
63
dÕŽpaisseur, il faut intercaler les plaquettes de
com-pensation C, dont lÕappareil est ŽquipŽ, ˆ
c™tŽ des charni•res.
820
870
820
870
BORD
BORD
ARRIERE
AVANT
PANNEAU LATERAL
DROIT
15
1052
820
CïTƒ
INTERIEUR
15
275
280
5765
132
C
29
Werbung
Kapitel
