Important Safety Instructions - Honeywell HS-216E Betriebsanleitung

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

Read through all the instructions before
starting to use the appliance. Keep this manual
in a safe place for future reference.
These instructions are also available on our
website. Please visit www.hot-europe.com.
• This appliance must only be operated as
instructed in this user manual.
• This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
• Do not touch the rotating fan blades with
any part of the body. This can cause personal
injury and damage.
• Clean the appliance regularly by following
the "Cleaning" section.
• This appliance is only designed for indoor use.
• Always switch the appliance off when not in
use, during cleaning or transport.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a hazard.
• Do not use this appliance if it is damaged or
shows any signs of possible damage, or if it
is not functioning properly. Disconnect the
power plug from the power socket.
4
COMPONENTS
(See page 3)
1. Front Grille
2. Grille Locking Ring
3. Blade
4. Plastic Nut
5. Rear Grille
6. Plastic Sleeve on Motor Shaft
7. Oscillating Control Knob
8. Neck
9. Control Knob
10. Extension Column
11. Height Adjustment Ring
12. Column
13. Stand Base
ASSEMBLY INSTRUCTIONS
(See page 3)
Stand Base Assembly
1. Fix the column on the stand using the handle screw (Fig. 1).
2. Adjust the extension column to the necessary height and
tighten the adjustment ring (Fig. 2).
Assembly of Blade and Grilles
1. Unscrew the spinner clockwise and the nut counter-clockwise
to separate them (Fig. 3).
2. Set the rear grille in the proper position with handle up.
3. Screw on plastic nut tightly to attach rear grille (Fig. 4).
4. Discard plastic sleeve on motor shaft. Install the blade onto
the shaft until it reaches the retaining pin.
5. Screw spinner onto motor shaft counter clockwise to blade
(Fig. 5).
6. Place grille locking ring around rear grille and then press
front grille into locking ring. Tighten tension screw with
screw driver (Fig. 6).
Fan to Base Assembly
1. Place fan assembly onto extension column (Fig. 7).
2. Tighten fan assembly screw with screw driver (Fig. 8).
OPERATING INSTRUCTIONS
The height of the fan can be adjusted by loosening the height
adjustment ring, carefully raising or lowering the fan to the
height required and then firmly tightening the height
adjustment ring.
Speed Knob
The speed of the fan is controlled by rotating the speed knob. The
number will indicate which of the three speeds is in effect:
0 = Off; 1 = Low; 2 = Medium; 3 = High
Oscillation
To make the fan oscillate, press down on the oscillating control
knob located on the top of the motor housing. To stop oscillation,
pull up on the knob.
Tilt Adjusting
To adjust the airflow upward or downward, loosen the screw,
gently push the grilles (1,5) to the desired position and retighten
the screw.
CLEANING, STORAGE AND DISPOSAL
CLEANING
• Switch the appliance off and remove the power plug from the
socket.
• Clean the outer surfaces of the appliance with a soft, damp
cloth. Do not use petroleum, thinners or any other chemicals.
Use your vacuum cleaner with the brush attachment to clean
the grids.
• Do not plunge the appliance into water or any other liquids
and do not pour water or any other liquids over the appliance.
STORAGE
• If you do not wish to use the appliance for a longer period,
clean it as described above.
• Store the appliance in a cool, dry location. Cover it up to
protect it from dust.
DISPOSAL
This symbol on the product or its packaging indicates that
the appliance cannot be treated as normal domestic
waste, but must be handed in at a collection point for
recycling electric and electronic appliances.
Your contribution to the correct disposal of this product protects
the environment and the health of your fellow men. Health and the
environment are endangered by incorrect disposal. Further information
about the recycling of this product can be obtained from your local
town hall, your refuse collection service, or in the store at which you
bought the product.
ENGLISH
WARRANTY/CONDITION OF PURCHASE
As a condition of sale, the purchaser assumes responsibility for the
proper use and care of this appliance in accordance with these printed
instructions. The purchaser or user must judge himself or herself
when to use the appliance and the length of use. Please keep your
receipt (or invoice) as your proof of purchase. The receipt must be
always presented when making a claim under the warranty period.
You may also be asked to provide the LOT number which gives you the
production date of your product. The LOT number is located on the
product and on the packaging. The production date can be deciphered
as follow: The first 3 numeric digits after LOT represents the day of
manufacture. The next 2 numeric digits represent the last two digits
of the calendar year of manufacture and the letter(s) at the end are a
factory identifier (E.g.: LOT No.: 12313 ABC this product was made on
the day 123, year 2013 at the factory code ABC).
NOTE: IN THE UNLIKELY EVENT THAT YOU EXPERIENCE A
PROBLEM WITH THIS PRODUCT PLEASE FOLLOW THE WARRANTY
INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO REPAIR THIS
PRODUCT YOURSELF. DOING SO WILL VOID THE WARRANTY AND
COULD CAUSE PROPERTY DAMAGE OR LEAD TO PERSONAL INJURY.
Technical modifications reserved.
This product carries the CE mark and is manufactured in
conformity with the Electromagnetic Directive 2004/108/EC,
the Low Voltage Directive 2006/95/EC and the RoHS Directive
2011/65/EU.
HS-216E
220-240V ~ 50Hz
50W
5