Specifications - Makita BUC250 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Red indicator
1-2. Button
1-3. Battery cartridge
2-1. Lock-off button
2-2. Switch trigger
3-1. Front hand guard
3-2. Lock
3-3. Unlock
4-1. Adjusting screw
5-1. Slightly slide
5-2. Move in the upright position
6-1. Press in
6-2. Loosen
6-3. Sprocket cover
6-4. Adjusting dial
7-1. Sprocket
8-1. Adjusting pin
9-1. Small hole
10-1. Press in

SPECIFICATIONS

Model
Guide bar length
Standard guide
Cutting length
bar
Type
Type
Pitch
Standard saw
chain
Gauge
No. of drive links
Number of teeth
Sprocket
Pitch
Overall length
Chain speed per minute
Net weight
Chain oil tank volume
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
*1 Weight, with largest battery cartridge, without guide bar and chain, empty oil tank, according to EN ISO 11681-2.
*2 Weight, with battery cartridge, guide bar, and chain, filled oil tank, according to EPTA-Procedure 01/2003.
WARNING: Use appropriate combination of the guide bar and saw chain. Otherwise personal injury may result.
Explanation of general view
10-2. Tighten
10-3. Loosen
11-1. Lever
12-1. Press in
12-2. Loosen
13-1. Low
13-2. High
13-3. Adjusting dial
13-4. Guide bar
13-5. Saw chain
14-1. Press in
14-2. Tighten
16-1. Hook
16-2. Belt
18-1. Oil tank cap
18-2. Oil tank opening
18-3. Oil inspection window
(for refilling the tank with oil)
18-4. Oil inspection window
BUC250
Sprocket nose bar
91VG
9.5 mm
(3/8")
1.3 mm
(0.05")
40
6
9.5 mm
(3/8")
576 mm
*1 4.0 kg
*2 4.5 kg
250 mm
24 cm
Carving bar Sprocket nose bar
91PX 25AP 91VG
6.35 mm
(1/4")
1.3 mm
(0.05")
60
9
6.35 mm
(1/4")
589 mm
8.3 m/s (500 m/min)
5
20-1. Lower guide
28-1. Felling area
31-1. Felling direction
31-2. Danger zone
31-3. Escape route
32-1. Scabbard (chain cover)
32-2. Battery cartridge
36-1. Small dust or particles
36-2. Slotted bit screwdriver
38-1. Sprocket
38-2. Locking ring
39-1. Locking ring
39-2. Sprocket
40-1. Limit mark
41-1. Brush holder cap
41-2. Screwdriver
UC250D
Carving bar
91PX 25AP
9.5 mm 6.35 mm
(3/8") (1/4")
1.3 mm 1.3 mm
(0.05") (0.05")
40 60
6 9
9.5 mm 6.35 mm
(3/8") (1/4")
577 mm 590 mm
4.0 kg
4.5 kg
3
85 cm
D.C. 36 V
BUC300 UC300D
300 mm
30 cm
Sprocket nose bar
90PX
9.5 mm
(3/8")
1.1 mm
(0.043")
46
6
9.5 mm 9.5 mm
(3/8") (3/8")
626 mm 627 mm
4.0 kg 4.0 kg
4.6 kg 4.6 kg