Kenwood KMM-106 Bedienungsanleitung Seite 17

Audio Settings
[AUDIO CONTROL]
[SUB-W LEVEL] [–15] to [+15] ([0]) Adjusts the subwoofer output level.
[BASS LEVEL] [–8] to [+8] ([+2])
[MID LEVEL] [–8] to [+8] ([+1])
[TRE LEVEL] [–8] to [+8] ([+1])
[EQ PRO] Adjusts your own sound settings for each source.
• The settings are stored to [USER] in [PRESET EQ].
(Before making an adjustment, select the source you want to adjust.)
[BASS ADJUST] [BASS CTR FRQ]
[BASS LEVEL]
[BASS Q FACTOR]
[BASS EXTEND]
[MID ADJUST] [MID CTR FRQ]
[MID LEVEL]
[MID Q FACTOR]
[TRE ADJUST] [TRE CTR FRQ]
[TRE LEVEL]
Default: [XX]
Adjusts the level to memorize for each source.
(Before making an adjustment, select the source
you want to adjust.)
[60]/[80]/[100]/[200]: Selects the center
frequency.
[–8] to [+8] ([+2]): Adjusts the level.
[1.00]/[1.25]/[1.50]/[2.00]: Adjusts the quality
factor.
[ON]: Turns on the extended bass. ;
[OFF]: Cancels.
[0.5KHZ]/[1.0KHZ]/[1.5KHZ]/[2.5KHZ]: Selects
the center frequency.
[–8] to [+8] ([+1]): Adjusts the level.
[0.75]/[1.00]/[1.25]: Adjusts the quality factor.
[10.0KHZ]/[12.5KHZ]/[15.0KHZ]/[17.5KHZ]:
Selects the center frequency.
[–8] to [+8] ([+1]): Adjusts the level.
[PRESET EQ] [DRIVE EQ]/[TOP40]/[POWERFUL]/[ROCK]/[POPS]/[EASY]/[JAZZ]/
[NATURAL]/[USER]: Selects a preset equalizer suitable to the music
genre.
• When the display demonstration is activated ([ON] is selected
initially, page 12), [POWERFUL] is automatically selected as the
[PRESET EQ].
– If you set [DEMO MODE] to [OFF] (page 12), [USER] is selected as
the default setting for [PRESET EQ].
• Select [USER] to use the settings made in [EQ PRO].
[BASS BOOST] [LV1]/[LV2]/[LV3]: Selects your preferred bass boost level. ;
[OFF]: Cancels.
[LOUDNESS] [LV1]/[LV2]: Selects your preferred low or high frequencies boost to
produce a well-balanced sound at low volume. ; [OFF]: Cancels.
[SUBWOOFER SET] [ON]: Turns on the subwoofer output. ; [OFF]: Cancels.
[LPF SUBWOOFER] [THROUGH]: All signals are sent to the subwoofer. ; [85HZ]/[120HZ]/
[160HZ]: Audio signals with frequencies lower than 85 Hz/120 Hz/
160 Hz are sent to the subwoofer.
[SUB-W PHASE] [REVERSE] (180°)/[NORMAL] (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
• Selectable only if a setting other than [THROUGH] is selected for
[LPF SUBWOOFER].
[FADER] [R15] to [F15] ([0]): Adjusts the front and rear speaker output balance.
[BALANCE] [L15] to [R15] ([0]): Adjusts the left and right speaker output balance.
[VOLUME OFFSET] For AUX: [–8] to [+8] ([0]) ; For other sources: [–8] to [0]: Presets the
initial volume level of each source by comparing to the FM volume level.
(Before adjustment, select the source you want to adjust.)
[SOUND RECNSTR] [ON]: Creates realistic sound by compensating the high-frequency
(Sound components and restoring the rise-time of the waveform that are lost in
reconstruction) audio data compression. ; [OFF]: Cancels.
• [SUB-W LEVEL]/[LPF SUBWOOFER]/[SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
11
ENGLISH