Gebrauch Und Wartung (Abmessungen Der Sensorspitze Und Einbaubohrung) - gefran M3 Betriebsanleitung

5.3 Gebrauch und Wartung (Abmessungen der Sensorspitze und Einbaubohrung)

Externe Kapillare
Entspricht die Einbaubohrung nicht den Spezifikationen, kann dies zu einem anomalen Verhalten und
zur Beschädigung des Sensors führen.
Die Einbaubohrung muss sauber und frei von Kunststoffrückständen sein.
85184E_Man_Drucksensoren für Temperaturanwendungen 07-2014_DEU
D1 1/2-20UNF
D2 .307/.305"
[7.80/7.75mm] [5.99/5.94mm
D3 .414/.412"
[10.52/10.46mm] [8.53/8.48mm]
A .219/.209 "
[5.56/5.31mm] [6.50/6.25mm]
B .450"
[11.43mm]
C 1.07"
[27.2mm]
D1 1/2-20UNF
D2 .313 ±0.001"
[7.95 ±0.02mm] [6.12 ±0.02mm]
D3 .454 ±0.004"
[11.53 ±0.1mm]
[8.74 ±0.1mm]
D4 .515" [13mm] .515" [13mm]
min.
A .225" [5.72mm] .263" [6.68mm]
min.
B .17" [4.3mm]
max.
C .75" [19mm]
Abmessungen
der Sensorspitze
D1 1/2-20UNF
D2 .307/.305"
[7.80/7.75mm]
D3 .414/.412"
[10.52/10.46mm]
A .125/.120 "
[3.18/3.05mm]
B .318/.312 "
[8.08/7.92mm]
C 81" [20.6mm]
M10x1.0 M14x1.5
.236/.234" .307/.305"
[7.80/7.75mm]
.336/.334" .475/.470"
[12.07/111.94mm]
.256/.246 " .236/.226 "
[5.99/5.74mm]
.430" .480"
[10.92mm] [12.19mm]
1.06" 1.28"
[26.9mm] [32.5mm]
M10x1.0 M14x1.5
.241 ±0.001" .319 ±0.001"
[8.10 ±0.02mm]
.344 ±0.004" .478 ±0.004"
[12.14±0.1mm]
.630" [16mm]
min.
min.
.240" [6.10mm]
min.
min.
.11" [2.8mm] .16" [4.0mm]
max.
max.
.75" [19mm] .75" [19mm]
Abmessungen der
Einbaubohrung
M18x1.5
.394/.392"
[10.01/9.96mm]
.630/.627"
[16.00/15.92mm]
.236/.226 "
[5.99/5.74mm]
.590"
[14.98mm]
1.34"
[34.0mm]
M18x1.5
.398 ±0.001"
[10.10 ±0.02mm]
.634 ±0.004"
[16.10 ±0.1mm]
.790" [20mm]
min.
.240" [6.10mm]
min.
.16" [4.0mm]
max.
.99" [25mm]
29