Optional Accessories - Makita DTR180 Betriebsanleitung

Error display and error tone
CAUTION:
During inspection, be sure to lock the trigger, turn the power off, and remove the battery
cartridge. F ailure to d o so ma y c ause an a c c i d ent.
CAUTION:
W hen you turn the power on, never bring your limbs or face close to the binding or rotating
parts of the tool tip. Otherwise, you may be injured.
CAUTION:
W hen the power is turned on, never touch the binding or rotating parts of the tool tip.
Otherwise, you may be injured.
CAUTION:
If an error tone sounds, or if the tool malfunctions, immediately stop using the tool.
Error tone and display
I f an error o c c urs, an error tone w ill soun d , an d an error number w ill be s h o w n on t h e d ispla y panel. R e f er to t h e
f ollo w ing table an d take appropriate a c tions. I f t h e error persists, ask Makita A ut h ori z e d S er v i c e C enters f or repairs.
Display
1
2
3
4
5
6
7
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. T h e use o f an y ot h er
a c c essories or atta c h ments mig h t present a risk o f
injury to persons. Only use accessory or attachment
f or its state d purpose.
I f y ou nee d an y assistan c e f or more d etails regar d -
ing t h ese a c c essories, ask y our lo c al Makita S er v i c e
C enter.
• T ie w ire
• Makita genuine batter y an d c h arger
NOTE: S ome items in t h e list ma y be in c lu d e d in t h e
tool pa c kage as stan d ar d a c c essories. T h e y ma y
d i f f er f rom c ountr y to c ountr y .
Symptom
T h e tool stops operating.
T h e tool stops operating.
T h e tool d oes not perf orm th e
ty ing proc ess in c ontinuous
ac tuation mod e.
T h e tool d oes not start.
T h e tool stops operating.
T h e tool stops operating.
T h e tool stops operating.
T h e tool d oes not start.
T h e tool stops operating.
Possible cause
T h e w ire h as been used up.
T ie w ire is not load ed .
W ire f eed ing h as f ailed .
T h e c url guid e is open.
T h e c ontac t plate is c augh t.
T h e battery h as been
d isc h arged .
T h e temperature of th e battery
c artrid ge is abnormally h igh .
T h e motor is ov erload ed .
Motor f ailure
T h e temperature of th e tool is
abnormally h igh .
T ool f ailure
18 ENGLISH
Solution
L oad new tie w ire.
L oad tie w ire.
C h ec k th e orientation of th e
tie w ire.
U nload th e tie w ire, and load
it again.
C lean th e path of w ire.
C lose th e c url guid e.
R elease th e c ontac t plate f rom
being c augh t.
R ec h arge th e battery .
C ool th e battery c artrid ge
d ow n.
R eplac e th e battery c artrid ge
w ith a rec h arged one.
D etermine th e c ause of th e
obstruc tion of th e motor rotation
and solv e th e problem.
C ool th e tool d ow n.
A sk Makita A uth oriz ed S erv ic e
C enters f or repairs.