Makita DTR180 Betriebsanleitung Seite 17

3. P us h t h e release le v er, an d lo c k it w it h t h e lo c k
le v er.
Fig.34: 1. R elease le v er 2. L o c k le v er
4. R emo v e t h e w ire reel f rom t h e tool.
NOTE: W h en w ire h as been use d up normall y ,
appro x imatel y 20 c m o f t h e w ire remains w oun d on
t h e reel. I n t h is state, repla c e t h e w ire reel w it h a ne w
one.
If it is difficult to remove the wire reel from the tool,
f ollo w t h e steps belo w .
1. I nsert t h e batter y c artri d ge into t h e tool, an d
turn t h e po w er on. T h e tool f ee d s t h e w ire an d c uts it
automati c all y .
2. L o c k t h e trigger, turn t h e po w er o f f , an d remo v e
t h e batter y c artri d ge.
3. R emo v e t h e w ire breaks using tools su c h as nip-
pers or pliers.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
T o maintain pro d u c t S A F E T Y an d R E L I A B I L I T Y ,
repairs, any other maintenance or adjustment should
be per f orme d b y Makita A ut h ori z e d or F a c tor y S er v i c e
C enters, al w a y s using Makita repla c ement parts.
Storage of the hex wrench
Store the hex wrench in the position shown in the figure.
Fig.35: 1. H e x w ren c h
Cleaning the cutter
W h en t h e tool is use d f or a long perio d o f time, d ust an d
w ire parti c les ma y be c ome a d h ere d to t h e c utter se c -
tion. I n su c h a c ase, d isassemble an d c lean t h e c utter
a c c or d ing to t h e f ollo w ing pro c e d ure.
I f a w ire is c aug h t in t h e c utter se c tion, t h e w ire c an be
remo v e d b y f ollo w ing t h e same pro c e d ure.
Disassembling and cleaning
1. L oosen bolts A an d B using t h e h e x w ren c h
in c lu d e d in t h e tool pa c kage.
Fig.36: 1. Bolt A 2. Bolt B 3. C onta c t plate c o v er
4. W ire gui d e B
NOTICE:
Do not forcibly remove any bolts that
cannot be removed using the hex wrench.
2. P ull t h e c onta c t plate c o v er up in t h e d ire c tion o f
t h e arro w an d remo v e it. Bolt B w ill be remo v e d at t h e
same time.
Fig.37: 1. C onta c t plate c o v er 2. Bolt B
3. R emo v e bolt A , an d remo v e w ire gui d e B.
Fig.38: 1. Bolt A 2. W ire gui d e B
4. T urn w ire gui d e B o v er an d c lean its insi d e.
Fig.39
5. R emo v e c utter A , c utter B, top plate, an d link arm
A f rom arm plate A . T h en, c lean t h em.
Fig.40: 1. C utter B 2. L ink arm A 3. C utter A 4. A rm
plate A 5. T op plate
Assembling
When cleaning is finished, assemble the parts accord-
ing to t h e f ollo w ing pro c e d ure.
Install cutter A and link arm A to fit the shape of
1.
arm plate A .
Fig.41: 1. C utter A 2. L ink arm A 3. A rm plate A
2. I nstall c utter B an d t h e top plate onto arm plate A .
( I nstall c utter B on c utter A an d link arm A . )
Fig.42: 1. C utter B 2. T op plate 3. A rm plate A
4. C utter A 5. L ink arm A
NOTICE:
Face the projection of cutter B down-
ward, and install the cutter as shown in the figure.
3. A lign t h e pipe o f t h e tool w it h t h e groo v e insi d e t h e
w ire gui d e B, an d assemble t h em.
Fig.43: 1. P ipe 2. G roo v e 3. W ire gui d e B
4. F i x w ire gui d e B b y temporaril y tig h tening bolt A .
Fig.44: 1. Bolt A 2. W ire gui d e B
5. I nstall t h e c onta c t plate c o v er in t h e d ire c tion o f
t h e arro w .
Fig.45: 1. C onta c t plate c o v er
6. F i x w ire gui d e B an d c onta c t plate c o v er se c urel y
b y tig h tening bolt A an d bolt B.
Fig.46: 1. W ire gui d e B 2. C onta c t plate c o v er
3. Bolt A 4. Bolt B
After assembling, confirm that the contact plate
7.
can move as shown in the figure.
Fig.47: 1. C onta c t plate
NOTE: I f t h e c onta c t plate is c aug h t, press it as
shown in the figure.
Fig.48
17 ENGLISH